Menu
Your Cart

Motor Controllers and Drivers

Model: 16CHPCA9685MOD
With this 16-channel pwm/servo control you can easily control 16 servo's or LEDs accurately via I2C. This module is based on the PCA9685 servo control from Adafruit and broadly corresponds: Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685 Specifications: Voltage V..
€6.00
Ex Tax:€4.96
Model: 16CHPCA9685MODHEAD
With this 16-channel pwm/servo control you can easily control servo's or LEDs via I2C. This module is based on the PCA9685 servo control of Adafruit and roughly corresponds: Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685 Specifications: Voltage Vcc pin: 3-5V V..
€5.00
Ex Tax:€4.13
Model: EASYDRIVER4.4
Easy motor control for a bipolar stepper motor (2 phase stepper motor). This is version 4.4 of the EasyDriver designed by Brian Schmalz, most of the information can be found on his page about this product: Easy Driver Stepper Motor Driver. Specifications: Voltage: 7 - 30V DC Signal volta..
€4.00
Ex Tax:€3.31
Model: A4988DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield. Specifications: Voltage range: 8-35V Maximum current: 1A (continuous), 2A (peak) Works with 3.3V and 5V signals Current limit that can be set with the potentiometer Supports full-step, half-..
€3.00
Ex Tax:€2.48
Model: A000079
The Arduino Motor Shield is based on the L298 driver. This module is able to control DC motors, stepper motors, relays and solenoids.  Specifications: Input voltage: 5-12V DC Motor controller: L298P (for 2 DC motors or 1 stepper motor) Max. current: 2A per channel or a maximum of 4..
€23.00
Ex Tax:€19.01
Model: TLSMOOTHER
With this TL-Smoother, vibrations in a stepper motor can be reduced. This makes the motor quieter and in the case of 3D printers it can lead to better prints. The effect is especially noticeable in combination with a DRV8825 or A4988 stepper motor driver.  Specifications: Connectors:..
€3.50
Ex Tax:€2.89
Model: CNCSHIELDV3
This popular CNC shield can be used to make your own CNC. The shield can be used in combination with A4988 stepper driver modules. This shield can control 4 step motors. Specifications: GRBL 0.8c compatible Can control 4 axles by means of smart control and 4 stepper driver modules Two ..
€5.00
Ex Tax:€4.13
Model: CNCSHIELDV4
This popular CNC shield can be used to make your own CNC. The shield can be used in combination with A4988 stepper driver modules. This shield can control 3 step motors. This CNC shield is especially for the Arduino Nano.  Specifications: GRBL 0.8c compatible Can control 3 axles by ..
€5.00
Ex Tax:€4.13
Model: DRV8825DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield. Specifications: Voltage range: 8.2-45V Maximum current: 2.5A per phase (continuous, with cooling), 1.5A per phase (continuous without cooling) Works with 3.3V and 5V signals Current limit that..
€4.50
Ex Tax:€3.72
Model: DRV8833MOD
A motor control for two DC motors or a bipolar stepper motor (2 phase stepper motor). The names of the connections are visible on the PCB. Specifications: Voltage range (signals): 0-5V Voltage range (power supply for motors): 3-10V DC Maximum current (per bridge): 1.5A (up to 500mA r..
€3.00
Ex Tax:€2.48
Model: HY-DIV268N-5A
Easy to set stepper motor control for a bipolar stepper motor .  Specifications: Voltage range (power supply): 8-42VDC (12-36V recommended) Voltage range (signals): 2.0-5.5V Maximum peak current per bridge (adjustable via dipswitch): 0.2A, 0.6A, 1.2A, 1.8A, 2.5A, 3.3A, 4.2A, 5..
€14.00
Ex Tax:€11.57
Model: L293D
A commonly used motor driver with built-in H-bridges to control, for example, two DC motors or a (small) stepper motor. See the datasheet for more information...
€0.50
Ex Tax:€0.41
Model: MOTORSHIELD
This shield is based on an Adafruit shield and offers control for two servo motors and four DC motors or two bipolar/unipolar stepper motors. The shield has a shift register built in which can save a large number of pins. Specifications: Input voltage(external power supply): 5-12V DC ..
€5.00
Ex Tax:€4.13
Model: L298N
A motor controller for two DC motors. Specifications: Voltage range (signals): 0 - 5V Voltage range (power supply for the motors): 5 - 35V DC Maximum current (per bridge): 2A The names of the connections are visible on the PCB. More information: Datasheet van L298N and ..
€5.00
Ex Tax:€4.13
Model: L9110S
A motor controller for two DC motors or one bipolar stepper motor, consisting of two L9110S chips. The names of the connections are visible on the PCB. More information: Datasheet..
€3.50
Ex Tax:€2.89
Model: LV8729DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. This is a quieter variant for the standard A4988 module. Specifications: Voltage range (VM): 6-36V Voltage range (VIO): 3.3-5V Maximum current: 0.8A per phase (continuous, with ..
€8.00
Ex Tax:€6.61
Model: M5STACK-U076
The 8Servos Hat is a basis for the M5 StickC*. The module consists of eight servo connections, an RGB LED, a battery holder with battery and a switch. The servos are controlled by a built-in STM32F030F4 microcontroller. The module is controlled with I2C by placing an M5StickC*on top. Specificatio..
€10.50
Ex Tax:€8.68
Model: M5STACK-M025-B
The GoPlus2 from M5Stack is a DC motor and servo driver that is controlled by an STM32F030 chip. This module contains 2 DC motor ports, and 4 servo motor ports. In addition, the GoPlus2 also has 3 Grove-B (GPIO) ports, and it is possible to receive and send IR signals. By means of the built-in Li-Po..
€15.00
Ex Tax:€12.40
Model: M5STACK-M021
The LEGO+ Module a motor driver especially for LEGO® motors. The module can control a total of 4 LEGO® motors. The module also has an XT30 connector to power the module. Specifications: Input voltage: 6-12V DC I2C address: 0x56 Motor driver: L293DD (2x) 4x LEGO® compatible..
€13.50
Ex Tax:€11.16
Model: M5STACK-M014
This is a servo driver module for the M5Core that can control up to 12 different servo motors. Specifications: Input voltage: 6-24VDC 12x Servo connections XT60 connector female XT60 connector male (included) ATMEGA328 chip control via I2C (0x53). Package content: 1x M5St..
€13.00
Ex Tax:€10.74
Model: M5STACK-M014-B
This is a servo driver module for the M5Core that can control up to 16 different servo motors. The module has a built-in voltage converter that brings the input voltage to the correct servo voltage. Specifications: Input voltage: 6-12V DC (via XT60 connector) Output voltage servo channels..
€17.00
Ex Tax:€14.05
Model: M5STACK-M012
This is a stepper motor expansion module for the M5Core with three DRV8825 stepper drivers. This allows you to connect three stepper motors to 1/32 step size.   Furthermore, additional modules are available such as a 5V fan module. Specifications: 3x DRV8825 stepper driver ..
€22.00
Ex Tax:€18.18
Model: RTKRPIMOTORCONTR
With this HAT for the Raspberry Pi you can control two DC motors. Specifications: Input voltage: 4-36V (max 12V recommended due to heat development) Maximum current: 1A SN754410 Driver PWM control possible to control the speed See the following page to get started with the board:..
€13.00
Ex Tax:€10.74
Model: SERVOTESTER
With this servo driver you can easily test the correct operation of servo's. The servo tester can test in 3 different methods (choose by 'select' button') : Manual mode: By adjusting the rotary knob the speed can be adjusted Neutral mode: The servo returns to the 'neutral..
€3.00
Ex Tax:€2.48
Model: STPMTREXPBOARD
An individual stepper motor extension board where a stepper motor driver can be installed. Specifications: Input voltage (power supply): max. 30V DC MS1, MS2 en MS3 control jumpers Control: Direction, speed, enable Motor connector: JST-XH 4 pins Size: 42 x 42 x 15mm Note: Pay a..
€4.00
Ex Tax:€3.31
Model: TB6600
Easy to set stepper motor control for a bipolar stepper motor .  Specifications: Voltage range (signals): 3.3-24V Voltage range (power supply): 9-42V (12-24V recommended) Maximum current per bridge (adjustable via dipswitch): 0.5A, 1.0A, 1.5A, 2.0A, 2.5A, 2.8A, 3.0A, 3.5A Dimensi..
€10.00
Ex Tax:€8.26
Model: TB6612FNG
A breakout board of a 1A Dual motor driver that is very easy to use. The pin headers are included. This can be soldered yourself if necessary. Read more about it here. Note: This is not an original product of sparkfun, but it functions in such a way...
€7.00
Ex Tax:€5.79
Model: TB67S109DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield. The motor driver is suitable for motors that require higher currents, such as a Nema 23 stepper motor.  Specifications: Voltage range: 10-47V Maximum current: 3A per phase (continuous, with c..
€8.00
Ex Tax:€6.61
Model: TMC2130DRIVERMODV1.1
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. This V1.1 has the SPI pins soldered upwards so that they are accessible from above. Specifications: Voltage range(VM): 5.5-45V Voltage range(VIO): 3.3-5V Maximum current: 1.2A per..
€10.50
Ex Tax:€8.68
Model: TMC2208DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. Specifications: Voltage range(VM): 5.5-36V Voltage range(VIO): 3.3-5V Maximum current: 1.2A per phase (continuous, with cooling), 2A peak per phase Works with 3.3V and 5V signals..
€8.00
Ex Tax:€6.61
Model: TMC2209DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. Specifications: Voltage range (VM): 4.75-29V Voltage range (VIO): 3.3-5V Maximum current: 2.0A per phase (continuous, with cooling), 2.8A peak per phase Works with 3.3V and 5V si..
€9.00
Ex Tax:€7.44
Model: TMC2225DRIVERMODV1.1
This TMC2225 is similar to the TMC2208 Motor Driver. This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. Specifications: Motor voltage range (VM): 4.75-36V Logic voltage range (VIO): 3-5V Maximum motor phase current: 1.4A RMS, 2.0A ..
€8.50
Ex Tax:€7.02
Model: TMC5160DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. This stepper motor driver is intended for motors with a higher power and amperage, suitable for, among other things, NEMA17 and NEMA23. Specifications: Voltage range (VM): 10-35V Vo..
€24.00
Ex Tax:€19.83
Model: TMC5161DRIVERMODV1.1
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. This stepper motor driver is intended for motors with a higher power and amperage, suitable for NEMA17 and NEMA23, among others. Specifications: Motor voltage range (VM): 10-35V Log..
€25.00
Ex Tax:€20.66
Model: ULN2003
The ULN2003 is an array of seven Darlington transistor pairs. With this, a signal can be amplified to 50V and 500mA per channel. The signal pins work with both 3.3V and 5V logic. The built-in flyback diodes protect the chip against inductive loads, such as the coils of an motor. Specifications: ..
€0.50
Ex Tax:€0.41
Model: VNH2SP30MOD
A motor controller for DC motors that can deliver up to 30A. Specifications: Voltage range (signals): 0-5V Voltage range (power supply for motors): 5-16V DC Maximum current (per bridge): 30A (note: cooling is required above 14A!) Recommended maximum current (per bridge): 14A Maximum..
€8.00
Ex Tax:€6.61
Model: VNH2SP30SHIELD
A motor controller for two DC motors or a bipolar stepper motor (2 phase stepper motor) that can deliver as much as 30A. This shield is based on the Sparkfun shield called "Monster Moto Shield". This product is not an orignal Sparkfun product, but offers the same functionality. Specifi..
€20.00
Ex Tax:€16.53
Model: WS-9724
With this Motor Control Shield you can control up to four DC motors or two stepper motors at the same time. With a jumper, the power supply circuit for the motors can be adjusted so that it receives a variable output voltage. Doing so allows motors with a lower voltage to be used by lowering the vol..
€9.00
Ex Tax:€7.44
Model: WS-17035
With this HAT you provide a Raspberry Pi with a 16-channel PWM/servo control via I2C. The HAT is designed for the Raspberry Pi Zero, but also works with other models. In addition, the module can also be used with other microcontrollers such as an Arduino or ESP via the external pin headers. The (..
€11.00
Ex Tax:€9.09
Model: WS-15275
With this HAT you provide a Raspberry Pi with a 16-channel PWM/servo control via I2C. The HAT is designed for the Raspberry Pi Zero, but also works with other models. In addition, the module can also be used with other microcontrollers such as an Arduino or ESP via the external pin headers. This ..
€11.00
Ex Tax:€9.09
Waveshare Stepper Motor HAT - for Raspberry Pi
New
Model: WS-15669
With this HAT for Raspberry two stepper motors can be controlled. The module also has a built-in voltage converter that can be used to power the Raspberry Pi. Specifications: Supply voltage: 8.2-28V DC (via 5.5mm DC jack) Signal voltage: 3.3V Motor driver: DRV8825 Maximum outp..
€15.00
Ex Tax:€12.40
Model: WMD1MTB6612SHIELD
A shield with a TB6612 motor driver for the (Wemos) D1 Mini. This motor driver can control two motors up to 1A. The motor driver is controlled via I2C, saving you a lot of pins. The asterisk on a pin indicates that the shield works via this pin. Inhoud verpakking:1x TB6612 Motor Shield for..
€5.00
Ex Tax:€4.13
Showing 1 to 42 of 42 (1 Pages)
1
false
false
true
Remove
Change
tr