Model: BTT-CB1-V2.2
A control board that may be used as an alternative to Raspberry Pi. This board has the same dimensions and interface as the RPi CM4.
The board can run the Klipper firmware and work as 3D printer controller, and is compatible with most BigTreeTech mo..
€30.00
Ex Tax:€24.79
Model: BTT-KRAKEN-V1.0
The BIGTREETECH Kraken motherboard is a very comprehensive motherboard with 8 integrated stepper motor drivers. This motherboard is ideal for large printers, in part because it supports high motor voltages (up to 60V) as wel as high motor currents...
€115.00
Ex Tax:€95.04
Model: BTT-MANTA-E3EZ-V1.0
The BIGTREETECH Manta series consists of convenient 3D printer motherboards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This E3EZ has the same form factor as a standard ender 3 motherboard, ma..
€48.00
Ex Tax:€39.67
Model: BTT-MANTAM4P-V2.2
The BIGTREETECH Manta series consists of convenient boards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This M4P version is based on an STM32G0 and can control up to 5 different stepper motors ..
€54.50
Ex Tax:€45.04
Model: BTT-MANTAM5P-V1.0
The BIGTREETECH Manta series consists of convenient boards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This M5P version is based on an STM32G0 and can control up to 6 different stepper motors ..
€64.50
Ex Tax:€53.31
Model: BTT-MANTAM8P-V1.1
The BIGTREETECH Manta series consists of convenient boards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This M8P version is based on an STM32G0 and can control up to 9 different stepper motors ..
€69.00
Ex Tax:€57.02
Model: BTT-OCTOPUSV1.1
The BigTreeTech Octopus is one of the most comprehensive 3D printer motherboards available. The board is powered by a powerful 32-bit processor and runs on Marlin or Klipper firmware. The firmware can be easily uploaded and updated with an SD card (n..
€51.00
Ex Tax:€42.15
Discontinued
Model: BTT-RAMPS1.6+
The RAMPS 1.6+ 3D printer motherboard from BIGTREETECH is suitable to use in combination with. an Arduino Mega and up to five stepper drivers (X, Y, Z, E0, E1). In addition, this motherboard has many other connections for LCD, Heated bed, End stops, ..
€9.50
Ex Tax:€7.85
Model: BTT-SKR3-EZ
The SKR 3 EZ is a very comprehensive motherboard for your 3D printer, on which you can use Marlin, Klipper or RepRap Firmware. This is one of the first bigtreetech boards with EZ drivers, these new drivers have integrated heat sinks, thanks to the so..
€69.00
Ex Tax:€57.02
Model: BTT-SKRMINIE3V2.0
This board is a very good basis for a DIY printer or as an upgrade for an Ender 3, the dimensions correspond to the original motherboard of an Ender 3 so you can easily replace it. The SKR Mini E3 V2.0 is driven by a 32-bit processor and has 4 silent..
€25.00
Ex Tax:€20.66
Model: BTT-SKRMINIE3-V3.0
This board is a very good basis for a DIY printer or as an upgrade for an Ender 3, the dimensions correspond to the original motherboard of an Ender 3 so you can easily replace it. The SKR Mini E3 V3.0 is driven by a 32-bit processor and has 4 silent..
€35.00
Ex Tax:€28.93
Model: BTT-SKRPICO-V1.0
The SKR Pico is a compact motherboard for your 3D printer, designed to be used with a Voron V0.1/0.2. The board is based on a Raspberry Pi RP2040 MCU and can control up to 5 different stepper motors with built-in TMC2209 stepper motor drivers. Furthe..
€29.50
Ex Tax:€24.38
Model: MKSGENLV1.0
A Marlin-based 3D printer board with a large number of extra features for your 3D printer.
The board is based on an ATMega2560 and can control five different stepper motors and two hotends. (drivers not included!)
Furthermore, the board h..
€29.50
Ex Tax:€24.38
Model: MKSGENLV2.1
A Marlin based 3D printer board with a lot of extra features for your 3D printer.
The board is based on an ATMega2560 and can control five different stepper motors and two hotends (drivers not included).
Furthermore, the board has a large..
€29.00
Ex Tax:€23.97
Model: RAMPS1.4
The RAMPS 1.4 control board is suitable to use in combination with an Arduino Mega and a maximum of five stepper drivers.
This board is mainly used for 3D printers.
The jumpers for the motor driver settings are included and the board is fully ass..
€5.50
Ex Tax:€4.55
Showing 1 to 15 of 15 (1 Pages)