Menu
Your Cart

There are technical issues at the PostNL sorting centers in Brabant. As we are located in Brabant, almost all mailbox packages are experiencing delays. We apologize for the inconvenience!

Humidity

AM2301 Temperature and Humidity Sensor
2-4 Weeks
Model: AM2301-MOD
The AM2301 is a very accurate temperature and humidity sensor. The sensor is a lot more accurate than the DHT11, and comparable to the DHT22. The sensor is relatively large, but this makes it easier to mount. See the manual under the "Downloads" t..
€6.00
Ex Tax:€4.96
Model: AM2320
A handy temperature sensor and humidity sensor...
€3.00
Ex Tax:€2.48
Model: AHT21B-MOD
A small temperature and humidity sensor in one. See the following page for a library for this sensor: Adafruit AHTX0..
€3.00
Ex Tax:€2.48
Model: AHT25-MOD
A small temperature and humidity sensor in one. See the following page for a library for this sensor: Adafruit AHTX0 Note: The pin spacing is not compatible with standard pin headers and DuPont connectors...
€3.00
Ex Tax:€2.48
Model: AM2122
A handy temperature and humidity sensor. Pinout (left to right from the front): VDD: Supply voltage SDA: Serial Data (One-Wire) GND: Ground NC: Not connected See the datasheet under the tab "Downloads" for more information. See..
€4.00
Ex Tax:€3.31
Model: DHT20
A handy temperature and humidity sensor in one. Pinout (left to right from the front): VDD: Supply voltage SDA: Serial Data (I2C) GND: Ground SCL: Serial Clock (I2C) See the datasheet under the tab "Downloads" for more information..
€3.00
Ex Tax:€2.48
Model: HR202L
A humidity-sensitive resistor for measuring humidity. Specifications: Maximum voltage: 1.5V AC Maximum power: 0.2mW Operating frequency: 500Hz ~ 2kHz (1kHz recommended) Measuring range: 20 - 95% RH Accuracy: ±5% RH Working temperat..
€1.00
Ex Tax:€0.83
Model: BME280MOD
A very compact barometer that works with I2C or SPI. The BME280 is an 3-in-1 module that can measure temperature, pressure and humidity. For more information see the datasheet under the tab "Downloads".  The module can only be powered with..
€7.50
Ex Tax:€6.20
Model: BME280LVLCNV
A very compact barometer that works with I2C. The BME280 is an 3-in-1 module that can measure temperature pressure and humidty For more information see the datasheet under the tab "Downloads". This version includes a level converter and voltage..
€8.50
Ex Tax:€7.02
Model: BME680LVLCNV
This module has four sensors in one that can measure temperature, air pressure, humidity and air quality. The module has a built-in level converter making it easy to use with both 3.3V and 5V microcontrollers. Specifications: Supply voltage:..
€15.50
Ex Tax:€12.81
Model: CCS811HDC1080MOD
This module contains a CCS811 digital gas sensor and an HDC1080 humidity and temperature sensor. This sensor module is intended for indoor use in combination with a microcontroller via an I2C interface. The CCS811 module is a digital gas sensor th..
€30.50
Ex Tax:€25.21
Model: DFROBOT-SEN0546 Brand: DFRobot
..
€10.00
Ex Tax:€8.26
Model: DFROBOT-SEN0527 Brand: DFRobot
..
€6.00
Ex Tax:€4.96
Model: DFROBOT-SEN0428 Brand: DFRobot
..
€10.50
Ex Tax:€8.68
Model: DFROBOT-SEN0528 Brand: DFRobot
..
€7.00
Ex Tax:€5.79
Model: DFROBOT-SEN0497 Brand: DFRobot
..
€9.00
Ex Tax:€7.44
Model: DFROBOT-SEN0137 Brand: DFRobot
..
€9.00
Ex Tax:€7.44
Model: DFROBOT-SEN0385 Brand: DFRobot
..
€21.00
Ex Tax:€17.36
Model: DHT11
A handy temperature and humidity sensor.Specifications: Measurement range Humidity: 20% - 90% RH (0-50 °C temperature compensation) Measurement range Temperature: 0 - +50 °C Air humidity precision: ±5.0% RV Temperature precision: ±2.0 °C ..
€2.50
Ex Tax:€2.07
Model: DHT22
A handy temperature and humidity sensor. This one is more precise than the DHT11. Specifications: Measurement range Humidity: 0 - 100% RH (0-50 °C temperature compensation) Measurement range Temperature: -40 - +80 °C Air humidity precisi..
€5.50
Ex Tax:€4.55
Model: DHT22MOD
DHT22 Module + Cables. A handy temperature sensor and humidity sensor. This is a lot more accurate than the DHT11. Humidity measurement range: 0% ~ 100% RH Measuring range temperature: -40 ~ +80 °C. Humidity accuracy: ±2.0% RH (typical),..
€6.00
Ex Tax:€4.96
Model: GY-SHT31-D
This is a very compact temperature and humidity sensor module...
€4.00
Ex Tax:€3.31
Model: M5STACK-A011-B Brand: M5Stack
The M5Stack BTC Standing Base is a standard for the M5Core. With the standard you provide the M5Core with power. It also has a built-in SHT30 temperature and humidity sensor that works with I2C communication. Specifications: Input voltage: 5..
€10.00
Ex Tax:€8.26
Model: M5STACK-U103 Brand: M5Stack
A CO2 sensor, humidity sensor and a temperature sensor in one of M5Stack...
€41.50
Ex Tax:€34.30
Model: M5STACK-U104 Brand: M5Stack
A CO2 sensor, humidity sensor and a temperature sensor in one of M5Stack...
€48.00
Ex Tax:€39.67
Model: M5STACK-U053-D Brand: M5Stack
..
€15.50
Ex Tax:€12.81
Model: M5STACK-U001-C Brand: M5Stack
The ENV III Unit is an upgrade of the ENV II and ENV Unit. This module has a temperature, humidity and air pressure sensor with a Grove connection for M5Stack. The difference between the ENV III Unit and the ENV II Unit is that this one uses the Q..
€8.00
Ex Tax:€6.61
M5STACK PM2.5 Air Quality Kit - ESP32 Development Kit
New
Model: M5STACK-K023-B Brand: M5Stack
This kit consists of an M5Stack Basic with pedestal and a PM2.5 Base module. This module consists of a PMSA003 laser dust sensor. The supplied pedestal contains a SHT30 temperature and humidity sensor...
€67.00
Ex Tax:€55.37
Model: RPISENSEHAT
The Sense HAT is an extensive module with numerous sensors made for a Raspberry Pi single board computer (SBC)...
€35.00
Ex Tax:€28.93
Model: SEEED-101990644
A handy temperature and humidity sensor from Seeed Studio that is easy to read via I2C. Specifications: Supply voltage: 2.0 - 5.5V DC Signal voltage: 2.0 - 5.5V (same as supply voltage) Communication: I2C I2C address: 0x38 (not cha..
€8.50
Ex Tax:€7.02
Model: SEEED-114992867
This SenseCAP air temperature and humidity sensor from Seeed Studio has a wide measuring range, and can be used at a long distance with LoRaWAN. Due to the dust-proof and splash-proof housing, this sensor can also be used outdoors. The sensor is easy..
€78.00
Ex Tax:€64.46
Model: SEEED-114992869
This SenseCAP sensor from Seeed Studio can measure CO2, temperature and humidity. In addition, it can be used wirelessly at a great distance with LoRaWAN. Due to the dust-proof and splash-proof housing, this sensor can also be used outdoors. The sens..
€150.00
Ex Tax:€123.97
Model: SI7021MOD
A compact temperature sensor and humidity sensor combined that works with I2C. Several applications are possible, such as a weather station or climate control. Specifications: Input voltage: 1.9 - 3.6 V (3.3 V recommended) Input current..
€11.00
Ex Tax:€9.09
Model: SI7021MOD2
A compact temperature and humidity sensor combined. Several applications are possible, such as for a weather station or climate control. In addition, the sensor has a built-in heater element to test the sensor or to evaporate condensation. Specifi..
€10.50
Ex Tax:€8.68
Model: SONOFFAM2301
This temperature and humidity sensor is to be used in combination with the Sonoff TH10 or TH16. Specifications: Measuring range temperature: -40ºC~+80ºC (± 0,5%) Measuring range humidity: 0%~99.9% RH (± 3% RH in 25ºC) Power supply: ..
€8.00
Ex Tax:€6.61
Model: SONOFF-SNZB-02
The Sonoff SNZB-02 is a very handy temperature and humidity sensor that works with the wireless ZigBee protocol. With this sensor module the temperature and humidity can be easily transmitted to other devices which can then, for example, turn on an a..
€9.00
Ex Tax:€7.44
Sonoff SNZB-02D - Temperature and Humidity Sensor with Display - ZigBee
New
Model: SONOFF-SNZB-02D
The Sonoff SNZB-02D is a very handy temperature and humidity sensor that works with the wireless ZigBee protocol. With this sensor module, you can easily transmit the temperature and humidity to other devices to turn on an air conditioner/fan, for ex..
€14.75
Ex Tax:€12.19
Model: SONOFF-THS01
This temperature and humidity sensor from Sonoff is made to be used together with the Sonoff TH Elite or TH Origin...
€7.50
Ex Tax:€6.20
Waveshare Environment Sensor Module - for Raspberry Pi Pico
New
Model: WS-20232 Brand: DFRobot
This environment sensor module from Waveshare is made for the Raspberry Pi Pico or other microcontrollers that use the same pin layout. This allows you to measure movement, temperature, humidity, light and air quality. Note: No Raspberry Pi Pico i..
€35.00
Ex Tax:€28.93
Model: WS-16864 Brand: Waveshare
With this HAT you provide your Raspberry Pi with various sensors that communicate via I2C. The HAT is designed for the Raspberry Pi Zero, but also works with other models. In addition, the module can also be used with other microcontrollers such as a..
€36.50
Ex Tax:€30.17
Model: WMD1MSHT30SHIELD
A shield with an SHT30 temperature and humidity sensor for the (Wemos) D1 Mini. The shield works with I2C where the I2C address is adjustable (see PCB) Pin headers are included with this shield (as shown) For more information, see this page: S..
€5.00
Ex Tax:€4.13
Showing 1 to 44 of 44 (1 Pages)
1
false
true
true
Remove
Change
tr