Model: VS1053MP3SHIELD
With this MP3 shield you can play various formats of music and have it controlled by your Arduino.
The music is on a micro-SD card that you can place in the micro-SD card holder on the shield.
In addition to playing music, this shield can also reco..
€11.00
Ex Tax:€9.09
Model: OS-USBMP3
This is an audio player that supports MP3/WAV files. It features an integrated audio amplifier, an SD card slot and can be controlled via UART.
A test code can be found in the .zip file under the tab "Downloads". Make sure that the folders are giv..
€7.50
Ex Tax:€6.20
Model: PAM8610
This is an incredibly powerful amplifier for its size. Partly due to the separate class-D design of PAM (Power Analog Microelectronics), which means that no coils are needed, it can be built in almost anywhere. You can control the volume with the pot..
€5.00
Ex Tax:€4.13
Model: PAM8610PRINTV2
This incredibly powerful amplifier is only 29mm x 25mm x 2.5mm!
This is due to the special class-D design of Power analog microelectronics which means no coils are required.
This makes it possible to build it in almost everywhere.
It is also equ..
€5.00
Ex Tax:€4.13
Model: 3-12VPASSIVEBUZ
A passive electromagnetic buzzer to indicate errors with an Arduino, for example. This buzzer is passive and must therefore still be controlled. This allows you to control the buzzer with different tones so that you can give different faults with dif..
€0.40
Ex Tax:€0.33
Model: 3-12VPASSIVEBUZ-PCMB-BUZZ
A passive electromagnetic buzzer to, for example, indicate errors with an Arduino. This buzzer is passive and therefore still needs to be controlled. This allows you to control the buzzer with different tones so that you can indicate different errors..
€1.00
Ex Tax:€0.83
Model: PCM5102MK2.0DAC
A DAC module that operates on the I2S (inter-IC sound) interface, suitable to convert a digital audio signal to an analog stereo signal. This is version 2.0 of this board with a 3.5mm audio jack connector...
€8.00
Ex Tax:€6.61
Model: PIEZOBUZ20MM
A simple buzzer to indicate errors with an Arduino, for example. This one is very flat. You can solder wires to it and then use it.
Voltage: 1.5-30V (peak-peak maximum)
Diameter: 20mm
Resonance frequency: 3.9±0.3KHz
Resonance resistance: ..
€0.15
Ex Tax:€0.12
Model: PIEZO12MMWIRES
A simple piezo buzzer to indicate errors with an Arduino or to detect vibrations. This is very flat and has a diameter of 12mm. This piezo is already pre-soldered with approximately 5cm long wires.
Specifications:
Diameter: 12mm
Resonation..
€0.30
Ex Tax:€0.25
Model: PIEZO20MMWIRES
A simple piezo buzzer to indicate errors with an Arduino or to detect vibrations.
This piezo is very flat and has a diameter of 20mm. This piezo is already pre-soldered with approximately 4cm long wires.
Specifications:
Diameter: 20mm
Res..
€0.50
Ex Tax:€0.41
Model: PIEZO35MMWIRES
A simple piezo buzzer to indicate, for example, errors with an Arduino or to detect vibrations.
This is very flat and has a diameter of 35mm. The piezo is mounted on a round plastic plate of 50mm in diameter for more firmness...
€0.50
Ex Tax:€0.41
Model: PIONEER-TS-A1371F
The Pioneer TS-A1371F is a compact 3-way speaker where everything is combined into one unit. Thanks to its smart design, an integrated woofer, midrange, and high-frequency tweeter work together perfectly. The result is a surprisingly full, balanced, ..
€55.00
Ex Tax:€45.45
Model: PIONEER-TS-A6971F
This A-Series Pioneer speaker features carefully selected materials to enhance bass and treble while delivering Pioneer's Open & Smooth sound concept, all in an easy-to-install package. This high-rated speaker set takes your DIY audio projects to..
€83.00
Ex Tax:€68.60
Model: PIONEER-TS-A6980F
This A-Series Pioneer speaker features carefully selected materials to enhance bass and treble while delivering Pioneer's Open & Smooth sound concept, all in an easy-to-install package. This high-rated speaker set takes your DIY audio projects to..
€63.25
Ex Tax:€52.27
Model: PIONEER-TS-G1310F
These speakers from Pioneer have a powerful sound with an excellent price-quality ratio. The rigid design is equipped with a number of mounting points so that the speakers are easy to mount in, for example, a DIY project. Thanks to the high sensitivi..
€29.00
Ex Tax:€23.97
Model: SEEED-107020029
A recorder module from Seeed Studio. With this module you can record sound and play back recorded audio. The Recorder V3 comes with a built-in microphone and an external speaker. There is a push button on the board to manually record and play sound (..
€20.25
Ex Tax:€16.74
Model: SPKR3W4O
A small 3W broadband speaker that will provide more than enough sound for most applications...
€2.00
Ex Tax:€1.65
Model: ZXACC-EXTSG-V12
An audio amplifier module that can be placed as a shield on the Smart Panlee 7 inch Serial Screen.
Note: No cables are included, they can be ordered separately here:
Molex Picoblade (compatible) cable 2p (for connecting speaker)
Molex..
€3.50
Ex Tax:€2.89
Model: XLY-C3
A compact passive 10W speaker that provides high audio performance for the majority of uses...
€2.75
Ex Tax:€2.27
Model: 78-F282A
A passive midrange 15W speaker that provides high audio performance for the majority of uses...
€10.50
Ex Tax:€8.68
Model: H96
A compact passive 3W broadband speaker that provides more than sufficient audio performance for the majority of uses...
€4.00
Ex Tax:€3.31
Model: 40-17M6-8
A compact passive 1W broadband mini speaker that provides more than sufficient audio performance for the majority of uses...
€1.00
Ex Tax:€0.83
Model: SPK40703W4OHM
A small speaker with a 4070 form factor...
€2.25
Ex Tax:€1.86
Model: SPKRSET-8OHM2W
A small speaker set. The set can be used separately with an amplifier. In addition, this set contains a JST-PH compatible connector to which both speakers are connected. With this, the set can easily be connected to a JST-PH female connector.
Spec..
€3.00
Ex Tax:€2.48
Model: BTAUDIORECEIVER-MH-M28
This MH-M28 Bluetooth audio receiver is a simple Bluetooth module to which audio can be streamed via Bluetooth from, for example, a laptop or telephone. The audio is then outputted on the audio jack and audio pins that are present on the board. This ..
€4.50
Ex Tax:€3.72
Model: TDA2030DIYKIT
With this do-it-yourself kit based on the TDA2030 chip you can make your own amplifier!
Specifications:
Voltage: 9-15VDC
TDA2030 chip
Speaker impedance: 4 to 8 ohms
Output power: 2x 14W (with 4 ohm speakers), 2x 9W (with 8 ohm sp..
€6.00
Ex Tax:€4.96
Model: TDA74982X100W
The TDA7498 chip has long been a player on the market of Class-D amplifiers. This standard variant of the TDA7498 chip is the version with a maximum of 2x 100W stereo output (at 6 Ohm). This amplifier is quite powerful. This requires a large battery ..
€18.00
Ex Tax:€14.88
Model: TDA7498E2X160W
The TDA7498E chip has long been a player on the market of Class-D amplifiers. The "E" variant of the TDA7498 chip is the most powerful version of this chip with up to 2x 160W stereo or 1x 220W mono output.
This amplifier is incredibly powerful. This..
€28.75
Ex Tax:€23.76
Model: TEENSYPROPSHIELD
With this shield for Teensy 3.2 and Teensy LC you expand the microcontroller with the following features:
Accelerometer (FXOS8700)
Gyroscope (FXAS21002)
Air pressure sensor and altimeter (MLP3115)
8MB Flash memory
Fast LED driver
2W A..
€20.50
Ex Tax:€16.94
Model: TEENSYPROPSHIELDLC
With this shield for Teensy 3.2 and Teensy LC you expand the microcontroller with the following features:
8MB Flash memory
Fast LED driver
2W Audio amplifier (LM48310)
For more information, see the following page: Prop Shield With..
€9.75
Ex Tax:€8.06
Model: TEENSYPT8211KIT
The Teensy PT8211 Audio Kit is a DIY digital to analog (DAC) converter shield for the Teensy 3.x or 4.x (two PCBs are included, one for 3.x and one fro 4.x). The PT8211 chip is a 16 bit DAC and provides a line-level output signal. This means that the..
€5.00
Ex Tax:€4.13
Model: TPA3116SUB
This TPA3116 amplifier is the mono version of the TPA3116 2x50W Audio amplifier and is ideal for a subwoofer.
Specifications:
Works between 12V and 24V DC (many combinations possible)
Very new and advanced chip from Texas Instrumen..
€11.50
Ex Tax:€9.50
Model: TPA3116BASSTREBLE-2.1
This 2.1 TPA3116 amplifier can supply up to 50W with two channels and a channel up to 100W. The format is still relatively compact and is ideal for crate and crate radio devices that also have an extra subwoofer speaker.
Specifications:
Works ..
€21.00
Ex Tax:€17.36
Model: TPA3116BT5.0-2.1
This 2.1 TPA3116 amplifier with Bluetooth 5.0 can supply up to 50W on two channels and one channel up to 100W. The size is still relatively compact and is ideal for crate radios that also have an extra subwoofer speaker.
Specifications:
..
€23.00
Ex Tax:€19.01
Model: TPA3116
This TPA3116 amplifier has the same compact size as the TA2024 and is therefore very suitable for crate radio's/DIY Boomboxes! The main difference is the power of this amplifier. Besides the huge power, this amplifier is suited for 5V, 12V and even 2..
€13.50
Ex Tax:€11.16
Model: TPA3116BT4.2BMT
This 2.1 TPA3116 amplifier with Bluetooth 4.2 can supply up to 50W on two channels. The size is relatively compact and is ideal for crate radios.
Specifications:
Works between 12V and 24V DC
Bluetooth 4.2 with approx. 8m range
Ve..
€17.25
Ex Tax:€14.26
Model: TPA3116BT4.0
This TPA3116 amplifier has about the same compact size of the TA2024 and is therefore ideal for in crate and crate radio and the like!
There is, however, a big difference between, and that is the power of this amplifier of course.
In addition to it..
€16.00
Ex Tax:€13.22
Model: TPA3116BASSTREBLE
This TPA3116 amplifier also has a bass, midtone and treble control. It's a bit bigger than our normal TPA3116 amplifier and the TA2024, but it's still ideal for a crate radio etc.!
We recommend our 24V power supply to get the most out of the ampl..
€17.00
Ex Tax:€14.05
Model: TPA3118-2X30W
This amplifier based on the TPA3118 chip can deliver up to 2x30W with two channels and is ideal for box and crate radios!..
€10.50
Ex Tax:€8.68
Model: SW-HF220-V1.0
This amplifier based on the TPA3118 chip can deliver up to 2x30W with two channels and is ideal for box and crate radios!..
€11.00
Ex Tax:€9.09
Model: SH-AUDIO-I2S
An audio shield for the TinyPICO, TinyS2/S3/C6 or ProS3 development boards. The shield contains an internal buzzer and can be connected to an external speaker, adjustable via the switch. Furthermore, the shield has an SD card slot and a connector for..
€12.50
Ex Tax:€10.33
Model: ISD1820
This module makes it possible to easily record your voice for 10 seconds and play it back.
The module comes with a speaker so that you immediately have sound, but can also be used as a megaphone module for example.
There is an LED on the module tha..
€5.50
Ex Tax:€4.55
Model: WS-20167
An audio module that can be placed as a HAT on a Raspberry Pi Pico (or other microcontroller with the same form factor).
Note: No Raspberry Pi Pico is included...
€15.50
Ex Tax:€12.81
Model: WS-14595
Brand: Waveshare
A small 5W speaker set from Waveshare. The set is made to be used in combination with certain Waveshare screens (see below), but can also be used separately with an amplifier.
Specifications (per speaker):
Rated power: 5W
Impedance: 8Ω
F..
€6.75
Ex Tax:€5.58
Model: WS-18833
A USB sound card with amplifier, ideal for connecting a small speaker to your PC or Raspberry Pi. Because the module uses the standard USB Audio protocol, no driver needs to be installed. The module is plug-and-play in combination with the following ..
€8.50
Ex Tax:€7.02
Model: WS-15668
Brand: Waveshare
With this audio HAT from Waveshare it is possible to easily connect a speaker or headphones to a Raspberry Pi. In addition, stereo sound can also be recorded with the built-in microphones.
Specifications:
Supply voltage: 5V DC
Signal volta..
€20.00
Ex Tax:€16.53