Model: ABX00042
The Arduino Portenta H7 is equipped with two processors that can perform parallel tasks. For example, this allows you to run Arduino on one core and MicroPython on the other and let them communicate with each other.
The board can be programmed with ..
€98.00
Ex Tax:€80.99
Model: ABX00050
..
€86.00
Ex Tax:€71.07
Model: ABX00061
The Nicla Voice enables always-on speech recognition with the powerful yet energy-efficient Syntiant® NDP120 Neural Decision microprocessor. It features a microphone, magnetometer, and smart 6-axis motion sensor, making it the ideal solution for pred..
€86.00
Ex Tax:€71.07
Model: AKX00045
An educational kit from Arduino with 10 science projects and multiple sensors. The set comes with an Arduino Nano RP2040 Connect with pre-installed software, so no programming experience is needed to work with the kit. The free Arduino Science Journa..
€209.25
Ex Tax:€172.93
Model: TPX00031
This all-in-1 Arduino Sensor Kit makes it easier than ever to learn the basics of Arduino. Compared to other kits, this kit requires no breadboard, soldering or even cabling! This makes it super easy to learn the basics of electronics and programming..
€38.50
Ex Tax:€31.82
Model: K000007
This is the Arduino Starter Kit developed by Arduino itself. The kit contains a project book with 15 simple projects and is therefore ideal to start with Arduino!
For more information: Arduino Starter Kit
The kit includes the following:
..
€99.00
Ex Tax:€81.82
Model: K000007-R4
This is the Arduino Starter Kit developed by Arduino itself. The kit contains a project book with 13 simple projects and is therefore ideal to start with Arduino!..
€95.00
Ex Tax:€78.51
Model: ABX00162
The Arduino Uno Q is a versatile board compatible with a wide range of Arduino shields. At its core, it combines an STM32U585 microcontroller with a QRB2210 microprocessor for AI acceleration and graphics processing. It includes 16GB of built-in stor..
€50.50
Ex Tax:€41.74
Model: ABX00173
The Arduino Uno Q is a versatile board compatible with a wide range of Arduino shields. At its core, it combines an STM32U585 microcontroller with a QRB2210 microprocessor for AI acceleration and graphics processing. It includes 16GB of built-in stor..
€84.00
Ex Tax:€69.42
Model: A000066
This is the original Arduino Uno R3 from Arduino itself. In addition to our own variant we also offer this one, e.g. if you want to support the Arduino community by buying their products.
The Arduino Uno R3 comes in a box together with some paperwo..
€25.00
Ex Tax:€20.66
Model: A000073
The Arduino Uno R3 is the standard microcontroller board from Arduino. This version of the board has an SMD ATmega328...
€25.00
Ex Tax:€20.66
Model: ABX00080
The Arduino Uno R4 Minima is the successor to the Uno R3 and is compatible with most Uno R3 shields. The Uno R4 Minima has a much more powerful Arm Cortex M4 microcontroller, and can be programmed and powered via the USB-C connector.
Note: The max..
€20.50
Ex Tax:€16.94
Model: ABX00087
The Arduino Uno R4 Wi-Fi is a successor to the Uno R3 and remains compatible with Uno R3 shields. The Uno R4 Wi-Fi has a much more powerful Arm Cortex M4 microcontroller, and can be programmed and powered via the USB-C connector. In addition to the U..
€27.50
Ex Tax:€22.73
Model: NANOATTINY88-COMP
The ATtiny88 Nano V3.0 is a compatible and cheaper version of the Arduino Nano V3.0. This variant is based on the ATtiny88 Microcontroller chip. This board contains a Micro USB connection with which the ATtiny can be programmed and powered. Usually N..
€5.00
Ex Tax:€4.13
Model: B-STOCK-9IN1-SENSORSHIELD
..
€3.50
Ex Tax:€2.89
Model: BTT-1020000405
A control board that may be used as an alternative to Raspberry Pi. This board has the same dimensions and interface as the RPi CM4.
The board can run the Klipper firmware and work as 3D printer controller, and is compatible with most BigTreeTech mo..
€36.00
Ex Tax:€29.75
Model: BTT-1030000089
This ESP module can be directly connected to most BigTreeTech boards, such as the SKR 2 and the OCTOPUS V1.1 boards. You can use the Wi-Fi module with ESP3D if you are using Marlin, or via Duet Web Control (DWC) if you are using RepRap Firmware.
S..
€8.00
Ex Tax:€6.61
Model: BTT-1020000456
The BIGTREETECH Kraken motherboard is a very comprehensive motherboard with 8 integrated stepper motor drivers. This motherboard is ideal for large printers, in part because it supports high motor voltages (up to 60V) as wel as high motor currents...
€125.00
Ex Tax:€103.31
Model: BTT-1020000407
The BIGTREETECH Manta series consists of convenient 3D printer motherboards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This E3EZ has the same form factor as a standard ender 3 motherboard, ma..
€46.00
Ex Tax:€38.02
Model: BTT-1020000419
The BIGTREETECH Manta series consists of convenient boards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This M4P version is based on an STM32G0 and can control up to 5 different stepper motors ..
€51.00
Ex Tax:€42.15
Model: BTT-1020000409
The BIGTREETECH Manta series consists of convenient boards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This M5P version is based on an STM32G0 and can control up to 6 different stepper motors ..
€61.75
Ex Tax:€51.03
Model: BTT-1020000410
The BIGTREETECH Manta series consists of convenient boards, with Raspberry Pi CM4/BIGTREETECH CM1 connector, to integrate your pi directly into the motherboard. This M8P version is based on an STM32G0 and can control up to 9 different stepper motors ..
€66.00
Ex Tax:€54.55
Model: BTT-1020000286
The BigTreeTech Octopus is one of the most comprehensive 3D printer motherboards available. The board is powered by a powerful 32-bit processor and runs on Marlin or Klipper firmware. The firmware can be easily uploaded and updated with an SD card (n..
€48.75
Ex Tax:€40.29
Model: BTT-1030000103
An adapter board for the Raspberry Pi CM4 or CB1 board from BigTreeTech to a RPi 4B layout.
The adapter board has a 40-pin GPIO header, multiple USB en Micro HDMI ports, a Micro-SD card slot and Ethernet connector.
This board also includes CSI..
€17.25
Ex Tax:€14.26
Model: BTT-RAMPS1.6+
The RAMPS 1.6+ 3D printer motherboard from BIGTREETECH is suitable to use in combination with. an Arduino Mega and up to five stepper drivers (X, Y, Z, E0, E1). In addition, this motherboard has many other connections for LCD, Heated bed, End stops, ..
€9.50
Ex Tax:€7.85
The SKR 3 is a very comprehensive motherboard for your 3D printer, on which you can use Marlin, Klipper or RepRap Firmware...
€67.25
Ex Tax:€55.58
Model: BTT-1020000417
The SKR 3 EZ is a very comprehensive motherboard for your 3D printer, on which you can use Marlin, Klipper or RepRap Firmware. This is one of the first bigtreetech boards with EZ drivers, these new drivers have integrated heat sinks, thanks to the so..
€67.25
Ex Tax:€55.58
Model: BTT-1020000201
This board is a very good basis for a DIY printer or as an upgrade for an Ender 3, the dimensions correspond to the original motherboard of an Ender 3 so you can easily replace it. The SKR Mini E3 V2.0 is driven by a 32-bit processor and has 4 silent..
€24.00
Ex Tax:€19.83
Model: BTT-1060000511
This board is a very good basis for a DIY printer or as an upgrade for an Ender 3, the dimensions correspond to the original motherboard of an Ender 3 so you can easily replace it. The SKR Mini E3 V3.0 is driven by a 32-bit processor and has 4 silent..
€33.50
Ex Tax:€27.69
Model: BTT-1020000327
The SKR Pico is a compact motherboard for your 3D printer, designed to be used with a Voron V0.1/0.2. The board is based on a Raspberry Pi RP2040 MCU and can control up to 5 different stepper motors with built-in TMC2209 stepper motor drivers. Furthe..
€28.25
Ex Tax:€23.35
Model: BREAKOUT-ESP-01
This is a breakout board for an ESP-01(S) module with which it can easily be used on a breadboard, for example. The ESP-01 module must be mounted on the board in such a way that the 3.3V and RX pin are on the side of the capacitor.
Note: Moun..
€1.00
Ex Tax:€0.83
Model: D1MINI
This D1 mini is basically a handy breakout board of the ESP-12F module. The USB to serial converter makes it easy to program, even as an Arduino. The board has a micro USB connection with which it can be programmed and/or fed. (micro USB cable not in..
€6.00
Ex Tax:€4.96
Model: 582693478794
This is a development board for the ESP32-WROOM Wi-Fi module. The ESP32-WROOM can easily be connected to this. With the help of this board, the module can be controlled and programmed without having to solder...
€9.50
Ex Tax:€7.85
Model: DEVBOARDEPS32WROVER
This is a development board for the ESP32-WROVER Wi-Fi module. The ESP32-WROVER can easily be connected to this. With the help of this board, the Wi-Fi module can be controlled and programmed without having to solder.
This board uses a CP2..
€8.00
Ex Tax:€6.61
Model: DEVBOARD-ESP8266
This is a development board for ESP8266 Wi-Fi modules. Using this board, the Wi-Fi module can be controlled and programmed without soldering.
Specifications:
Compatible ESP boards: ESP-01, ESP-01S, ESP-07, ESP-07S, ESP-12E, ESP-12F, ESP-12S ..
€10.25
Ex Tax:€8.47
Model: DFROBOT-DFR0270
Brand: DFRobot
There is no product description available yet. See the following page for information about this product: DFRobot Accessory Shield for Arduino
Note: Due to the PCB design, the relay cannot be used with mains voltage, use a maximum of 30V...
€25.50
Ex Tax:€21.07
Model: DFROBOT-DFR0282
Brand: DFRobot
A small development board from DFRobot based on the ATmega32u4 from Atmel (Microchip Technology)...
€10.75
Ex Tax:€8.88
Model: DFROBOT-DFR0816
Brand: DFRobot
This board can be programmed in Arduino IDE as an Arduino Leonardo...
€10.75
Ex Tax:€8.88
Model: DFROBOT-DFR0868
Brand: DFRobot
The Beetle ESP32-C3 comes with an Expansion Board PCB for extra pins, including an FPC connector for certain DFRobot display modules...
€10.25
Ex Tax:€8.47
Model: DFROBOT-DFR1117
Brand: DFRobot
The Beetle ESP32-C6 from DFRobot is an Arduino IoT development board with a compact design and supports various wireless communication protocols...
€6.25
Ex Tax:€5.17
Model: DFROBOT-DFR0959
A small development board from DFRobot based on the RP2040 chip from Raspberry Pi...
€8.50
Ex Tax:€7.02
Model: DFROBOT-DFR0010
Brand: DFRobot
A development board from DFRobot based on the design of the Arduino Nano...
€11.00
Ex Tax:€9.09
Model: DFROBOT-TEL0092
A UART to Wi-Fi module from DFRobot, with the form factor of an XBEE module. If you have a development/adapter board with an XBEE module connector, you can easily expand it with Wi-Fi. The module communicates via UART with AT commands...
€7.50
Ex Tax:€6.20
Model: DFROBOT-TEL0168
Brand: DFRobot
This wireless BLE sensor beacon from DFRobot can collect data from a digital or analog sensor and broadcast the value via BLE. Other devices with Bluetooth, such as a smartphone or microcontroller with Bluetooth (e.g. an ESP32) can then read out the ..
€17.25
Ex Tax:€14.26
Model: DFROBOT-DFR1075
Brand: DFRobot
This development board from DFRobot is an ESP32-C6 based board with Wi-Fi, Bluetooth, Zigbee and Thread support. The board has a USB-C connector with which it can be programmed and/or powered (USB cable not included)...
€7.25
Ex Tax:€5.99