Model: 2.4GHZANTSMASMALL90
An antenna for, for example, Wi-Fi or Bluetooth.
Specifications:
Gain: 3dBi
Impedance: 50Ω
Frequency range: 2400-2500MHz
Connector: SMA male
Orientation: 90 degrees
Dimensions: 48 x 17 x 8mm
Package contents:
1x 2.4GHz A..
€2.00
Ex Tax:€1.65
Model: 2.4GHZANTSMAUFL5DBI
An antenna for, for example, Wi-Fi or Bluetooth.
Specifications:
Gain: 5dBi
Impedance: 50Ω
Frequency range: 2400-2500MHz
Connector: uFL (I-PEX) female or SMA male
Orientation: Adjustable
Dimensions: 197 x 13 x 13mm
Package con..
€2.50
Ex Tax:€2.07
Model: 2.4GHZANTSMAUFL
Specifications:
Connector type: uFL (I-PEX)
Amplification: >3dBi
Impedance: 50 Ohm
Frequency range: 2400Mhz - 2500Mhz
Maximum input power: 50W..
€2.00
Ex Tax:€1.65
Model: 2.4GHZANTUFL
Specifications:
Connector type: uFL (I-PEX)
Amplification: 3dBi
Impedance: 50 Ohm
Frequency range: 2400Mhz - 2483Mhz
Total length: 10-15cm
Note: It may be that the black cover is shorter than shown in the image, however, this does ..
€1.50
Ex Tax:€1.24
Model: 3CHPWMMOD
A PWM module with LCD screen and 8 buttons for control.
Specifications:
Working voltage: 3.3 ~ 30V
Frequency Response: 1Hz ~ 150KHz
Frequency Accuracy: Accuracy in each range is approximately 2%
Signal load capacity: the output current..
€4.00
Ex Tax:€3.31
Model: 433MHZANTSMAUFL
Specifications:
Connector type: SMA & uFL (I-PEX)
Adapter cable length: 10 cm
Gain: >3 dBi
Impedance: 50 Ohm
Frequency range: 423MHz - 443MHz
Maximal input power: 50W..
€2.50
Ex Tax:€2.07
Model: 433MHZANT
This spiralwound 433Mhz antenna can perfectly send or receive a nice signal. And they are much more compact than the long monopole antennas!
Dimensions:
Length of the antenna: 20.5mm
Diameter: 5mm
Total length: 34.5mm..
€0.50
Ex Tax:€0.41
Model: 433MHZANTSMASMALL90
Specifications:
Gain: 3dBi
Impedance: 50Ω
Frequency range: 423-443MHz
Connector: SMA male
Orientation: 90 degrees
Dimensions: 48 x 17 x 8mm
Package contents:
1x 433MHz Antenna..
€2.00
Ex Tax:€1.65
Model: 433MHZANTUFL
This spiral shaped 433Mhz antenna is built as a spring and has an uFL (I-PEX) connector.
Specifications:
Length of the antenna: 26mm
Connector type: uFL (I-PEX)
Gain: 3 dBi
Impedance: 50 Ohm
Frequency: 433MHz
Diameter: 4.2 mm..
€1.50
Ex Tax:€1.24
Model: 433MAFSTAND
You can easily control an input with the remote control and the receiver. The remote control has 4 buttons that can control 4 outputs on the receiver. The 12V battery for the transmitter is included. This is already in the remote control. A red LED i..
€5.00
Ex Tax:€4.13
Model: 433MKIT
Receiver module specifications:
Voltage: 5V (DC)
Static current: 4mA
Receiver Frequency: 433MHz
Receiver sensitivity: -105dB
External antenna: 32cm single-core wire, wound into a spiral
Dimensions (L x W): 30 x 14mm
Transmitter m..
€2.50
Ex Tax:€2.07
Model: 6TO10AVRISP
An adapter that makes it easier to program your arduino with an AVR ISP programmer.
The pinout is written on both sides of the circuit board...
€1.50
Ex Tax:€1.24
Model: 868MHZANTSMASMALL
Specifications:
Connector type: SMA (pin in the middle sticking out)
Strengthening: 2dBi
Impedance: 50 Ohm
Frequency range: 868Mhz/900Mhz/915Mhz
Length: 5cm..
€3.00
Ex Tax:€2.48
Unknown
Model: GSMMODA6
With the A6 GSM/GPRS module you can make and receive calls, send text messages* and surf the internet via GPRS with your Arduino. The module can be powered with 5V through the micro USB connection.
Specifications:
Microcontroller: A6 chip
..
€8.00
Ex Tax:€6.61
Model: ESP8266-01-1M
This module offers you the possibility to connect your Arduino to WiFi for a very low price.
The ESP8266 module works with the normal UART port on your Arduino and can connect to networks, form your own network (hot spot) or both. The possibilitie..
€4.00
Ex Tax:€3.31
Model: ESP-01S
This module offers you the possibility to connect your Arduino to WiFi for a very low price. This "S" version of the ESP-01 module has minor improvements in the PCB compared to the normal ESP-01 module.
The ESP8266 module works with the normal UAR..
€4.00
Ex Tax:€3.31
Model: ESP8266-07S-4M
This ESP-07S is a version of the ESP8266 module series with 4MB memory and has an uFL connector on board for an external WiFi antenna. (this has to be purchased separately!)
This module offers you the possibility to connect your Arduino to WiFi fo..
€5.00
Ex Tax:€4.13
Model: ESP8266-12F-4M
This module offers you the possibility to connect your Arduino to WiFi for a very low price.
The ESP8266 module works with the normal UART port on your Arduino and can connect to networks, form your own network (hot spot) or both. The possibilitie..
€5.00
Ex Tax:€4.13
Model: ESP8266-12S-4M
This ESP-12S is an improved model with respect to the ESP-12F module, but is not a direct replacement in connection with the missing pins at the bottom of the module. Since these pins are not used in most cases, it is in most cases a replacement for ..
€4.50
Ex Tax:€3.72
Model: NRF24L01+Z
A very easy to use wireless communication module that uses the 2.4GHz frequency.
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, particularly suitable for industrial control applications.
125 Chann..
€2.50
Ex Tax:€2.07
Model: NRF24L01+PA-LNA
An easy wireless communication module that uses the 2.4 GHz band.
This variant of the NRF24L01+ module also has a PA (Power amplifier) ​​and LNA (Low noise amplifier) ​​built in for a wider range.
Maximum speed to 2Mbps, GFSK m..
€5.00
Ex Tax:€4.13
Model: A000024
The Arduino Ethernet Shield 2 has a W5500 ethernet controller and a microSD card reader.
Specifications:
Input supply voltage: 5V DC (to be received from the Arduino board)
Ethernet controller: W5500 with internal 32K buffer
Connec..
€29.25
Ex Tax:€24.17
Model: ATGM336H-5N-31
A GPS module that works with UART (TX and RX) signals. The corresponding GPS antenna is included.
Specifications:
Voltage range (VCC): 5V DC
I/O Voltage: 3.3V
Standard baud rate: 9600
Uses the ATGM366H-5N-31 GPS module
Works with GPS..
€11.00
Ex Tax:€9.09
Model: AC-RX2/CS
This receiver is a lot more sensitive than the receiver from the standard 433Mhz kit that we also offer.
This way you can receive better signals from other 433Mhz transmitters.
Specifications:
Voltage: 4.5 - 5.5V DC
Power (in..
€6.50
Ex Tax:€5.37
Model: RX-4MM5/F
This receiver is a lot more sensitive than the receiver from the standard 433Mhz kit that we also offer.
This way you can receive better signals from other 433Mhz transmitters.
Specifications:
Voltage: 4.5 - 5.5V DC
Current (..
€8.00
Ex Tax:€6.61
Discontinued
Model: C2541BLE-CC41A
This bluetooth 4.0 module has a lot of functionality built inside, including sending as an iBeacon or for standard serial communication.
In addition, the software on the module can be upgraded to get more functionality. We recommend to update the so..
€8.00
Ex Tax:€6.61
Model: BT-04MOD
With this bluetooth module it is very easy to send serial data to your phone, tablet, pc or other SPP-C modules. This bluetooth module can run only in slave mode.
Specifications:
Input voltage: 3.6 - 6V
Signal voltage: 3.3V (gebruik een le..
€4.00
Ex Tax:€3.31
Model: HC-02
With this Bluetooth module you can easily send data serially to e.g. your phone, tablet or on HC-05 and HC-06 modules. This Bluetooth module can only serve as a Slave.
Specifications:
Supply voltage: 3.2 - 6V DC
Signal voltage: 3.2 - 6V DC..
€5.50
Ex Tax:€4.55
Model: HC-05
With this bluetooth module you can easily send serial data to (for example) your mobile phone, tablet or other HC-05 modules. This bluetooth module can either be used as a master or slave.
Specifications:
Power Supply voltage: 3.2 - 6V DC
..
€18.00
Ex Tax:€14.88
Model: HC-05PCB
With this bluetooth module you can easily send data serially to eg. your phone, tablet or other HC-05 modules. This bluetooth module can serve both as master and slave.
Specifications:
Supply voltage: 3.3V
Signal voltage: 3.3V (use a level..
€18.00
Ex Tax:€14.88
Model: HC-06
With this Bluetooth module it is very easy to send data to your phone, tablet or other HC-05 modules. This module is slave only!
Specifications:
Input voltage: 3.2 - 6V DC
Signal voltage: 3.2 - 6V DC
Range: around 10m (in open ..
€17.00
Ex Tax:€14.05
Model: HC-07DMA
With this Bluetooth module you can easily send data serially to, for example, your telephone, tablet or other Bluetooth modules. This Bluetooth module can only serve as a slave.
For more information, see the (Chinese) datasheet under the tab "Down..
€8.00
Ex Tax:€6.61
Model: HC-07DSL
With this Bluetooth module you can easily send data serially to, for example, your telephone, tablet or other Bluetooth modules. This Bluetooth module can only serve as a slave.
For more information, see the (Chinese) datasheet under the tab "Down..
€8.00
Ex Tax:€6.61
Model: HC-08
With this HC-08 Bluetooth module you can easily send data serially to, for example, your phone, tablet, other HC-08 modules. This Bluetooth module can serve as Master or Slave.
Specifications:
Supply voltage: 3.2 - 6V
Signal voltage: 3.2 -..
€8.00
Ex Tax:€6.61
Model: HC-08PCB
With this Bluetooth module you can easily send data serially to for example your phone, tablet or other HC-08 modules. This Bluetooth module can serve as both Master and Slave.
Specifications:
Supply voltage: 3.3V
Signal voltage: 3.3V* (no..
€6.50
Ex Tax:€5.37
Model: HC-42
With this HC-42 bluetooth module you can easily send data serially to, for example, your phone, tablet, other (HC-42) bluetooth modules. This bluetooth module can serve as Master and Slave.
Specifications:
Supply voltage: 3.2-6V DC
Signal ..
€9.00
Ex Tax:€7.44
Model: HC-42PCB
With this HC-42 bluetooth module you can easily send data serially to, for example, your phone, tablet, other (HC-42) bluetooth modules. This bluetooth module can serve as Master and Slave.
Specifications:
Supply voltage: 3.2-6V DC
Signal ..
€7.50
Ex Tax:€6.20
Model: CANSHIELD
With this CAN Shield you can make contact with your Arduino with a CAN bus, for example from a car.
The shield uses the MCP2515 CAN Controller chip in combination with the MCP2551 CAN transceiver.
Specifications:
SPI speed up to 10Mhz
CAN..
€12.00
Ex Tax:€9.92
Model: CC2500RFMOD
An easy wireless RF communication module with the TI CC2500 chip that can use the various bands. The module works through SPI communication.
Specifications:
Voltage: 1.8 - 3.6V DC
Effective frequency range: 2400 - 2483.5MHz
Current (max)..
€6.50
Ex Tax:€5.37
Model: CC2500RFMOD-PCB
An easy wireless RF communication module with the TI CC2500 chip that can use the various bands. The module works through SPI communication. This RF board has a low power consumption, so it will be able to work on a power supply for a long time ..
€5.50
Ex Tax:€4.55
Model: CC2530UART
A module to send and receive UART wirelessly via 2.4Ghz Zigbee.
You can use two modules to send data or multiple modules to send/receive data to multiple modules.
Specifications:
Input voltage: 3.3-5.5 VDC
Current: <30 mA
Data rate: ..
€8.00
Ex Tax:€6.61
Model: CC2531USB-ZIGBEE
This CC2531 USB Stick is a complete ZigBee transceiver with a 9051 CPU and a USB interface in one chip. In addition, this module contains 2 buttons, 2 LEDs and 8 IO pins that can be programmed to allow sensors to work with this ZigBee module, for exa..
€7.75
Ex Tax:€6.41
Model: ESP01CH340USB
A simple USB to serial converter to communicate with an ESP-01 module.
Specifications:
3.3VTTL voltages
Chip: CH340 (drivers)
See the images for the connection orientation. Note: The ESP-01 module is not included.
It is also possib..
€2.50
Ex Tax:€2.07
Model: CH340USB
A simple USB to serial converter with selectable voltage through a jumper. Specifications:
3.3V-5V TTL voltages
Converts TTL logic levels to computer RS232 levels
Power supplies: 5V, 3.3V, GND (min)
RX (3.3V-5V)
TX (3.3V-5V)
Chip: CH3..
€2.50
Ex Tax:€2.07
Model: CH340EUSB
A USB to serial converter that can be configured for 3.3V and 5V using a jumper...
€2.50
Ex Tax:€2.07
New
Model: DFROBOT-TEL0073
Brand: DFRobot
This Bluno Bee is a Bluetooth module from DFRobot with XBee form factor. To be used with, for example, the Xbee V3 Arduino Adapter Shield to connect to an Arduino. The firmware can be updated via the micro USB connection...
€10.50
Ex Tax:€8.68
New
Model: DFROBOT-TEL0092
A UART to Wi-Fi module from DFRobot, with the form factor of an XBEE module. If you have a development/adapter board with an XBEE module connector, you can easily expand it with Wi-Fi. The module communicates via UART with AT commands...
€7.50
Ex Tax:€6.20