Menu
Your Cart

Adapter Boards

B-STOCK - Joystick Shield with NRF24 and Bluetooth adapter
B-Stock
Model: JOYSTICKSHIELD-BSTOCK
NOTE: This product is a B-Stock variant of our following product: Joystick Shield with NRF24 and Bluetooth adapter. B-Stock products are products that can no longer be sold normally due to a certain defect. In this case, the bluetooth and I2C conn..
€3.00
Ex Tax:€2.48
Model: DEVBOARDEPS32WROVER
This is a development board for the ESP32-WROVER WiFi module. The ESP32-WROVER can easily be connected to this. With the help of this board, the WiFi module can be controlled and programmed without having to solder. This board uses a CP210..
€18.00
Ex Tax:€14.88
Model: DEVBOARD-ESP8266
This is a development board for ESP8266 Wi-Fi modules. Using this board, the Wi-Fi module can be controlled and programmed without soldering. Specifications: Compatible ESP boards: ESP-01, ESP-01S, ESP-07, ESP-07S, ESP-12E, ESP-12F, ESP-12S ..
€10.50
Ex Tax:€8.68
Model: DFROBOT-DFR0270
There is no product description available yet. See the following page for information about this product: DFRobot Accessory Shield for Arduino Note: Due to the PCB design, the relay cannot be used with mains voltage, use a maximum of 30V...
€25.50
Ex Tax:€21.07
Model: DFROBOT-DFR0265
..
€10.50
Ex Tax:€8.68
Model: DFROBOT-DFR0165
..
€12.50
Ex Tax:€10.33
Model: DFROBOT-DFR0762
..
€6.00
Ex Tax:€4.96
Model: DFROBOT-DFR0171
..
€9.50
Ex Tax:€7.85
Model: DFROBOT-DFR0836
..
€5.00
Ex Tax:€4.13
Model: DFROBOT-DFR0131
..
€10.00
Ex Tax:€8.26
Model: JOYSTICKSHIELD
This shield has four handy buttons and a joystick. There are also pins available to easily connect your NRF24L01 or Bluetooth (HC-06) module to your Arduino. Specifications: Joystick with push button present in combination with four pushbutt..
€5.00
Ex Tax:€4.13
Model: NANOEXPAN
A board to make the pins of an Arduino Nano slightly more accessible. On the DC jack a voltage of 7-12V can be offered, up to 500mA current. The Nano must be placed so that the USB connector of the Nano is on the same side as the DC jack connection...
€5.00
Ex Tax:€4.13
Model: OS-NANOIOEXPBOARD
This Open-Smart Nano IO Expansion Board is a shield for the Arduino (Or Arduino compatible) Nano, with which you can give the Nano an Uno layout. In addition to the Uno layout, all Digital I/O pins and Analog pins have an extra pin, and 5V and GND ha..
€6.00
Ex Tax:€4.96
Orange Pi Zero Expansion Board
On request
Model: OPZEROEXPANSIONBOARD
An expansion board Orange Pi Zero, with this expansion board the following components are added to your Orange Pi Zero: 2x USB 2.0 ports 1x 3.5 mm jack port (audio) 1x IR receiver 1x microphone Dimensions: 41.5x39mm. Also seperate..
€4.50
Ex Tax:€3.72
Model: RPIGPIOEXTBOARDKIT
A GPIO extension kit so you can easily use the Raspberry Pi pins on a breadboard. The GPIO Extension Board has the pins in the same order as the Raspberry Pi and has pin indications on the GPIO extension board. The kit consists of a 40-cm cable t..
€4.50
Ex Tax:€3.72
Model: RDJOYSTICKSHIELD
This shield has four handy buttons and a joystick. There are also pins available to easily connect your NRF24L01 or Xbee module to your Arduino. Specifications: Joystick with push button present in combination with four colored pushbuttons..
€6.00
Ex Tax:€4.96
Model: RDNANOIOWIRELESS
This board gives you the possibility to connect various wireless boards to your Arduino Nano. The board supports the nRF24L01(+), ESP8266 ESP-01(S), APC220 and xBee modules. In addition, the board has separate pins with power supply next to it, m..
€5.00
Ex Tax:€4.13
Model: RAMPSFANEXT
This module offers the possibility to connect two fans to the Ramps 1.4 3D Printer Control Board, and also to control them with a PWM signal. Specifications: Input voltage: 5-20VDC Maximum current per channel: 500mA Number of fan connect..
€4.00
Ex Tax:€3.31
Screw Terminal Shield - Mega-Due compatible
2-4 Weeks
Model: SCREWSHIELDMEGASOLD
With this Screw Shield you can easily screw the wires to the pins on Mega-layout compatible boards. All available pins on the screw terminals have a pin description on the PCB. Dimensions: 120 x 77 x 11mm (height measured from bottom of PCB to to..
€12.00
Ex Tax:€9.92
Model: SCREWSHIELDMEGA
With this Screw Shield you can easily screw the wires to the pins on Mega-layout compatible boards. All available pins on the screw terminals have a pin description on the PCB. Dimensions (assembled): 120 x 77 x 11mm (height measured from bottom ..
€15.00
Ex Tax:€12.40
Model: SCREWSHIELDNANOSOLDERED
With this pre-soldered shield you can easily screw wires to the pins on boards with the form factor of an Arduino Nano. The pin descriptions are listed on the PCB. Package contents: 1x Screw Terminal Shield..
€3.50
Ex Tax:€2.89
Model: SCREWBOARDNANO
With this Screw Board you can easily screw the wires to the pins on Nano-layout compatible boards. All available pins on the screw terminals have a pin description on the PCB. Note: This product still has to be soldered!..
€3.00
Ex Tax:€2.48
Model: SCREWSHIELDV2
With this Screw Shield you can easily screw the wires to the pins on Uno-layout compatible boards. All available pins on the screw terminals have a pin description on the PCB. Note: This board has the SDA and SCL pins as pins, but these are not c..
€5.00
Ex Tax:€4.13
Model: SEEED-103030000
With this shield for the Seeeduino/Arduino Uno you provide the microcontroller with 16 Grove connectors. With the Grove connectors other Seeed Studio modules can be easily connected. Grove connectors types: 4x I2C Grove connector 1x UART&n..
€4.50
Ex Tax:€3.72
Model: SEEED-103030356
This Expansion Board for the Seeeduino XIAO provides the microcontroller with a variety of accessories. For example, the board has an OLED display, a buzzer and a microSD card adapter. In addition, the module also contains a connection for a Li-ion/..
€17.50
Ex Tax:€14.46
Model: SEEED-103030275
A Grove HAT for the Raspberry Pi 4. With this extension of your Raspberry Pi you have access to 15 different Grove connectors. With the help of a built-in MCU (STM32) you also provide the Raspberry Pi with an 8-channel ADC. Specifications: S..
€13.00
Ex Tax:€10.74
Model: SEEED-103100124
With this shield for the Seeeduino Nano/Arduino Nano you provide the microcontroller with 8 Grove connectors. With the Grove connectors other Seeed Studio modules can be easily connected. Specifications: 1x I2C Grove connector 1x UART ..
€3.00
Ex Tax:€2.48
Model: SEEED-103020312
This Grove shield for the Seeeduino XIAO provides the microcontroller with 8 Grove connectors. Via the Grove connectors, other modules from Seeed Studio can easily be connected. In addition, the shield also contains a connection for a Li-ion/Li-..
€6.00
Ex Tax:€4.96
Model: TEENSYAUDIOBOARD-4.0
With this adapter you can add 16-bit high-quality stereo audio to your project in combination with a Teensy 4.0. In addition to a stereo audio output, this module also has a mono microphone input for recording sound. (Microphone not included) For..
€16.25
Ex Tax:€13.43
Model: OCTOWS2811
With this adapter thousands of WS2811/WS2812 (B) LEDs can be controlled with a single Teensy 3.2. For more information, see this page: Teensy 3.2 OctoWS2811 Adapter Note: The OctoWS2811 Adapter is shown with the Teensy 3.2. The Teensy 3.2 is ..
€13.00
Ex Tax:€10.74
Model: TEENSYPT8211KIT
The Teensy PT8211 Audio Kit is a DIY digital to analog (DAC) converter shield for the Teensy 3.x. The PT8211 chip is a 16 bit DAC and provides a line-level output signal. This means that the signal is not intended to connect speakers directly, b..
€5.00
Ex Tax:€4.13
Model: TEENSYWIZ820SDCARD
With this adapter you can connect a WIZ820io or WIZ850io ethernet module and/or a micro SD card to your Teensy. For more information, see this page: WIZ820io & Micro SD Card Adapter Note: This product does not include pin headers...
€8.00
Ex Tax:€6.61
Model: WS-15082
A Waveshare E-Paper shield for Arduino. This allows you to connect different Waveshare e-Paper/E-ink displays to an Arduino (compatible) microcontroller. Specifications: Supply voltage: 3.3-5V DC Signal voltage: 3.3-5V Interface: SPI C..
€14.00
Ex Tax:€11.57
Model: WMD1CONSHIELD
A shield for the (Wemos) D1 mini with a TFT connector, two I2C connectors and an IO connector. With this shield you can easily connect a TFT display or make I2C connections. The cables are not included, but are sold separately: TFT cable I..
€2.00
Ex Tax:€1.65
Model: XBEESHIELDV3
A Xbee V3 adapter shield for an Arduino. With this shield your Arduino can communicate with other Xbee/Zigbee modules. Xbee module is not included. The switch on the shield can be used to switch between USB and the Xbee module.(switch RX a..
€4.50
Ex Tax:€3.72
Showing 1 to 36 of 36 (1 Pages)
1
false
true
true
Remove
Change
tr