Model: VM-WSSA130
This kit contains everything you need to builld your own christmas tree with lights. An extended manual is included in this kit.
Note: 9V Battery is not included...
€8.50
Ex Tax:€7.02
Model: VM-WSSA100B
This kit contains everything you need to builld your own christmas tree with lights. An extended manual is included in this kit.
Note: 9V Battery is not included...
€8.50
Ex Tax:€7.02
Model: DIYDSO13805K
Portable oscilloscope with 3.5-6V connection (eg a 5V adapter, USB adapter, USB power bank or 3x/4x AA batteries).
Put your own oscilloscope together with this DIY kit:
2.4 inch 240x320 pixels LCD pre-soldered on PCB
In this kit all SMD ..
€30.00
Ex Tax:€24.79
Model: D2-1TRACKING-CARKITDIY
An intelligent DIY car kit that can follow a black colored line on the ground using 2 white LEDs and 2 photosensitive resistors. This car does not need to be programmed, and it is only necessary to solder all parts to the PCB mounting plate. The car ..
€9.00
Ex Tax:€7.44
Model: LM317CERPOTDIYKIT
With this do-it-yourself kit you make an adjustable voltage regulator based on the LM317.
Specifications:
Input voltage: 5.0-25VDC, 6.0-20VAC
Maximum output voltage: Input voltage-2.5V
Maximum output current: 1.0A
PCB size: 62x44mm
..
€4.00
Ex Tax:€3.31
Model: LM317STDPOTDIYKIT
With this do-it-yourself kit you make an adjustable voltage regulator based on the LM317.
Specifications:
Input voltage: 5.0-25VDC, 6.0-20VAC
Output voltage: 1.25VDC-12VDC
Maximum output current: 1.0A
PCB format: 60x32mm
Note: A h..
€4.00
Ex Tax:€3.31
Model: LM3915LVLINDDIYKIT
With this do-it-yourself kit you create an audio level indicator yourself!
Specifications:
Voltage: 9 - 12V DC
Suitable for headphone/aux voltage level*
PCB format: 62 x 26mm
*Don't use on speaker outputs of amplifier!
Contents o..
€4.00
Ex Tax:€3.31
Model: M5STACK-K039
Brand: M5Stack
The M5STACK ATOMIC Proto Kit is a DIY proto kit designed for the M5ATOM series. The module can be connected directly via the 9 pins on an M5ATOM. The kit consists of a PCB with connection material and a housing with accessories.
Specificatio..
€11.00
Ex Tax:€9.09
Model: M5STACK-K011-B
Brand: M5Stack
This is an prototype module for the M5Core with a blank circuit board, power input and mounting options for wall mounting or DIN rails.
This circuit board is specifically intended for the M5Stack Core and can be installed as an extra layer on it. ..
€13.00
Ex Tax:€10.74
Model: M5STACK-M032
Brand: M5Stack
This is a prototype module with a height of 13.2mm for the M5Stack ESP32 Core and Core 2 with a blank printed circuit board, header pins and other connectors that connect the M5Stack Core. These headers are not connected to pins on the PCB.
This c..
€5.00
Ex Tax:€4.13
Model: NE555BLINKDIYKIT
With this do-it-yourself kit you can apply the NE555 chip in a LED blink module! You can change the blinking frequency with the potentiometer.
Specifications:
Voltage: 12VDC
PCB format: 40x40mm
Contents of the kit:
1x PCB
16x ..
€4.00
Ex Tax:€3.31
Model: PSRPISUPSWITCH
With this kit you make a power switch that automatically shuts off the power when you have turned off the Raspberry Pi. Turning on the Raspberry is then a push of a button on the module. In addition, the module also has a hard shutdown that can be us..
€15.00
Ex Tax:€12.40
Model: PSBRIGHTPI
With this kit you make a light module for the camera for the Raspberry Pi. The LEDs and headers must be soldered. The LED driver and I2C interface are pre-soldered.
The module uses an I2C interface, therefore it can also be used in combination wit..
€15.00
Ex Tax:€12.40
Model: PROTOSHIELDKITUNOLEO
A protoshield for an Arduino Uno or Leonardo. This is a DIY kit with two LEDs and two tactile switches.
Package contents:
1x Protoshield PCB
2x 330 ohm resistor
1x 1k ohm resistor
2x Tactile switch
1x Yellow LED
1x Green LED
2x 1..
€3.50
Ex Tax:€2.89
Model: RTKRPITRAFFICHAT
Traffic light HAT kit for Raspberry Pi. The HAT has 3 extra large LEDs, a buzzer and a tactile switch that must be soldered yourself. The series resistors and a 40 pin female header are pre-soldered.
Package contents:
1x PCB with 40 pin fema..
€9.50
Ex Tax:€7.85
Model: TDA2030DIYKIT
With this do-it-yourself kit based on the TDA2030 chip you can make your own amplifier!
Specifications:
Voltage: 9-15VDC
TDA2030 chip
Speaker impedance: 4 to 8 ohms
Output power: 2x 14W (with 4 ohm speakers), 2x 9W (with 8 ohm sp..
€6.00
Ex Tax:€4.96
Model: TEENSYETHERNETKIT-4.1
With this DIY kit you provide the Teensy 4.1 with an ethernet connection.
This product comes with loose parts and still needs to be soldered.
For more information, see this page: PT8211 Ethernet Kit..
€6.00
Ex Tax:€4.96
Model: TEENSYPT8211KIT
The Teensy PT8211 Audio Kit is a DIY digital to analog (DAC) converter shield for the Teensy 3.x or 4.x (two PCBs are included, one for 3.x and one fro 4.x). The PT8211 chip is a 16 bit DAC and provides a line-level output signal. This means that the..
€5.00
Ex Tax:€4.13
Showing 1 to 18 of 18 (1 Pages)