2-4 Weeks
Model: 6IN1USBSERIALMOD
A USB to serial converter that supports 6 different modes that are easy to configure with a number of switches (see image)...
€9.00
Ex Tax:€7.44
Model: 6TO10AVRISP
An adapter that makes it easier to program your arduino with an AVR ISP programmer.
The pinout is written on both sides of the circuit board...
€1.50
Ex Tax:€1.24
Model: ESP01CH340USB
A simple USB to serial converter to communicate with an ESP-01 module.
Specifications:
3.3VTTL voltages
Chip: CH340 (drivers)
See the images for the connection orientation. Note: The ESP-01 module is not included.
It is also possib..
€2.50
Ex Tax:€2.07
Model: CH340USB
A simple USB to serial converter with selectable voltage through a jumper. Specifications:
3.3V-5V TTL voltages
Power supplies: 5V, 3.3V, GND (min)
RX (3.3V-5V)
TX (3.3V-5V)
Chip: CH340 (drivers)
With the supplied jumper you can co..
€2.50
Ex Tax:€2.07
Model: CH340EUSB
A USB to serial converter that can be configured for 3.3V and 5V using a jumper...
€2.50
Ex Tax:€2.07
Model: CH340N-USB-C
A simple USB to serial converter...
€2.00
Ex Tax:€1.65
Model: ESPLINKV1.0
This ESP LINK can be used for firmware upgrades, serial port debugging and programming the ESP8266 ESP-01(S). This ESP LINK is supported by the "Arduino IDE", "ESP8266Flasher" and "Espressif Flash Download Tools". The ESP8266 ESP-01(S) can go directl..
€4.00
Ex Tax:€3.31
-programmer-ch430-600x600w.jpg "ESP LINK - ESP8266 ESP-01(S) Programmer - CH340C")
Model: ESPLINKCH340CV1.0
This ESP LINK can be used for firmware upgrades, serial port debugging and programming the ESP8266 ESP-01(S). This ESP LINK is supported by the "Arduino IDE", "ESP8266Flasher" and "Espressif Flash Download Tools". The ESP8266 ESP-01(S) can go directl..
€2.50
Ex Tax:€2.07
Model: ESP-PROG
This ESP Programmer is a handy module for programming and debugging an ESP32 or ESP8266. In addition, the JTAG debugging function is available for ESP32. The programmer is easy to connect to a computer using the Micro USB port. This ESP programmer ha..
€18.50
Ex Tax:€15.29
Model: ESP32-CAM-MB
This is a shield that has been specially developed for the ESP32- CAM - Wi-Fi and Bluetooth Board with OV2640 Camera. The ESP32-CAM is a very handy module, but it lacks a USB connection that makes it easy to upload new code. Due to the USB connection..
€2.75
Ex Tax:€2.27
Model: FISCHL-I2C-MP-USB
I2C-MP-USB is a interface to connect I2C devices via USB to a host system. It aims to easily control I2C slaves with highly portable code...
€27.00
Ex Tax:€22.31
Model: FISCHL-USBLINI-EB
USBlini is an interface to connect a LIN bus via USB to a host system. It provides easy access to LIN bus devices and can act as both master and slave. It features a logic analyzer function to sample the logic levels on the LIN RX line...
€31.50
Ex Tax:€26.03
Model: FT232USBCABLE
You can call it the most reliable USB to serial converter that you can find!
Many operating systems support this standard chip. If it does not install automatically, then look for the driver for your operating system here .
Specifications:
..
€9.00
Ex Tax:€7.44
Model: FT232USB
The most reliable usb to serial converter that you can find! This is almost indispensable if you want to be able to program Pro Mini (automatically) .
Many operating systems support this chip by default. If it is not automatically installed, pleas..
€7.50
Ex Tax:€6.20
New
Model: FT232USB-C
A USB to serial converter that can be configured for 3.3V or 5V using a jumper...
€7.50
Ex Tax:€6.20
Model: LILYGO-H494-Q320
The TTGO T-U2T from LilyGO is a USB to serial converter with USB-C connector which can be used (or even required) to program certain boards from LilyGO TTGO...
€6.50
Ex Tax:€5.37
Model: LILYGO-H439
This USB to serial converter is suitable for programming the LilyGO TTGO T-Internet PoE.
Specifications:
Connector: USB-C and micro USB
USB to serial converter: CH340C
Dimensions: See images
CH340 drivers:
Windows
Mac OSX
..
€3.50
Ex Tax:€2.89
Model: LILYGO-F308
This "USB stick" from LilyGO can be used to simulate USB devices, such as a keyboard. The USB can be programmed in Arduino IDE...
€10.75
Ex Tax:€8.88
Model: M5STACK-A105
Brand: M5Stack
The ESP32 downloader kit from M5Stack is a USB to serial adapter module that is ideal for programming or debugging an ESP32 and ESP8266. In addition to the standard RX and TX pins, the module also has connections for GPIO 0 and the enable pin of the ..
€8.00
Ex Tax:€6.61
Model: M5STACK-S006
Brand: M5Stack
The M5Stack ISP Serial Programmer is a USB to serial converter with USB-C connector which can be used to program ESP32 microcontrollers. ..
€6.50
Ex Tax:€5.37
Model: M5STACK-M020
Brand: M5Stack
The M5Stack USB Module is an expansion for the M5Core. This module adds a USB-port (type A), 10 GPIO pins and 2 power outputs each for 3.3V and 5V to the M5Core.
Specifications:
For use with the M5Core
MAX3421E Peripheral/Host Contro..
€15.50
Ex Tax:€12.81
Model: M5STACK-M020-V12
Brand: M5Stack
The M5Stack USB Module is an extension for the M5Core based on the MAX3421E. This module expands the M5Core with a USB port (type A) and extra GPIO pins...
€15.00
Ex Tax:€12.40
Model: OL-ESP-PROG-C
This ESP32 and ESP8266 programmer with cables from Olimex is suitable for programming the following ESP chips: ESP8266, ESP32, ESP32-S2, ESP32-C3, ESP32-C6. This programmer ensures that the ESP chip automatically enters and exits bootloader mode so t..
€6.50
Ex Tax:€5.37
Model: PL2303GC-CABLE
A cable with a built-in USB to serial converter...
€6.00
Ex Tax:€4.96
Model: ZXACC-ESPDB
The ZXACC-ESPDB is a USB to serial converter specifically designed for programming Panlee products...
€6.00
Ex Tax:€4.96
Model: STLINKV2-COMP
The ST-LINK V2 Compatible is an in-circuit debugger and programmer for the STM8 and STM32 microcontrollers.
Package content:
1x ST-LINK V2 Compatible
1x 4p female -> 4p female dupont cable
Tools for the ST-LINK V2: Driver + Fi..
€7.50
Ex Tax:€6.20
Model: USBHOSTSHIELD
This shield can easily be placed on an Arduino Uno, Arduino Mega or Arduino Due. The shield makes a USB host of the microcontroller such that, for example, a mouse or keyboard can be connected to the Arduino.
The following types of devices are sup..
€12.50
Ex Tax:€10.33
New
Model: USBPDTRIG
This USB PD trigger module allows you to request specific voltages (5V, 9V, 12V, 15V and 20V) from a USB-PD power supply. In addition to USB PD, other protocols are also supported. Use the button to switch between voltages. If the LED next to a volta..
€4.00
Ex Tax:€3.31
Model: USBASP
A programmer to provide your AVR with new software. For example, if you want to burn a new Arduino bootloader into an AVR chip.
A 10 pin flatcable with connectors is included.
This works well in combination with the adapter to 6-pins for your Ardu..
€4.50
Ex Tax:€3.72
Model: WS-21442
Brand: Waveshare
A USB to serial converter that can be configured for 3.3V and 5V using a jumper. If the jumper is completely removed, it is also possible to connect an external power supply to the VCCIO pin, making the module compatible with other voltages from 1.8V..
€4.00
Ex Tax:€3.31
Model: WS-21443
A USB to serial converter that can be configured for 3.3V and 5V using a jumper. If the jumper is completely removed, it is also possible to connect an external power supply to the VCCIO pin, making the module compatible with other voltages from 1.8V..
€4.00
Ex Tax:€3.31
Model: WS-7605
Brand: Waveshare
A USB to serial converter. The VCCIO pin on this module is depending on the jumper connected to the USB voltage or to the internal 3.3V output of the CP2101...
€5.50
Ex Tax:€4.55
2-4 Weeks
Model: WS-6170
A USB to serial converter that can be configured for 3.3V and 5V using a jumper...
€8.00
Ex Tax:€6.61
Model: WS-20646
A USB to serial converter that can be configured for 3.3V and 5V using a jumper. ..
€8.00
Ex Tax:€6.61
Model: WS-21550
A USB to serial (UART) converter.
Note: This product may only be used for business research and development or industrial applications...
€5.50
Ex Tax:€4.55
Model: WS-17939
A USB to serial (UART) converter.
Note: This product may only be used for business research and development or industrial applications...
€8.50
Ex Tax:€7.02
Model: WS-15817
A module made by Waveshare that converts a USB signal to RS232, RS485, or TTL UART.
Note: Only one of RS232, RS485 and TTL can be converted to USB at a time. Also, RS232, RS485 and TTL cannot be converted between each other.
Note: This product ..
€22.00
Ex Tax:€18.18
Model: WS-20265
A USB to serial converter that can be configured for 3.3V and 5V using a jumper. If the jumper is completely removed, it is also possible to connect an external power supply to the VCCIO pin, making the module compatible with other voltages from 1.8V..
€4.00
Ex Tax:€3.31
Model: WS-20645
A USB to serial converter that can be configured for 3.3V and 5V using a jumper. If the jumper is completely removed, it is also possible to connect an external power supply to the VCCIO pin, making the module compatible with other voltages from 1.8V..
€4.00
Ex Tax:€3.31
Showing 1 to 40 of 40 (1 Pages)