Model: VM-WSSA130
This kit contains everything you need to builld your own christmas tree with lights. An extended manual is included in this kit.
Note: 9V Battery is not included...
€8.50
Ex Tax:€7.02
Model: WS-18550
A firm metal housing for a Raspberry Pi 4 including an ICE Tower CPU Cooling Fan - Low Profile. This protects the Raspberry Pi and cools it properly at the same time (see iamges).
Specifications:
Suitable for: Raspberry Pi 4B
Case materia..
€29.50
Ex Tax:€24.38
Model: ANALOGVOLTMETER10V
This analogue voltmeter displays the voltage in the old-fashioned way with a pointer.
Specifications:
Voltage range: 0-10VDC
Accuracy: ± 2.5%
Only suitable for DC voltages.
Dimensions: 63.8 x 56 x 10.3mm (panel only, withou..
€5.00
Ex Tax:€4.13
Model: ANALOGVOLTMETER20V
This analogue voltmeter displays the voltage in the old-fashioned way with a pointer.
Specifications:
Voltage range: 0-20VDC
Accuracy: ± 2.5%
Only suitable for DC voltages.
Dimensions: 63.8 x 56 x 10.3mm (panel only, withou..
€5.00
Ex Tax:€4.13
Model: ANALOGVOLTMETER30V
This analogue voltmeter displays the voltage in the old-fashioned way with a pointer.
Specifications:
Voltage range: 0-30VDC
Accuracy: ± 2.5%
Only suitable for DC voltages.
Dimensions: 63.8 x 56 x 10.3mm (panel only, withou..
€5.00
Ex Tax:€4.13
Model: ANALOGVOLTMETER50V
This analogue voltmeter shows the voltage in the old-fashioned way with a pointer.
Specifications:
Voltage range: 0-50VDC
Accuracy: ± 2.5%
Only suitable for DC voltages.
Dimensions: 63.8 x 56 x 10.3mm (panel only, without p..
€5.00
Ex Tax:€4.13
Model: ST-2065D
A 65 Watt, temperature adjustable soldering iron from Atten.
Specifications:
Supply voltage: 230V AC
Maximum power soldering iron: 65W
Temperature range: 250 - 480°C
Temperature stability: ±1°C
Package contents:
1x Atten ST-..
€30.00
Ex Tax:€24.79
Model: HC-05BACKPLANE
This backplane is intended to solder an HC-05, HC-06, HM-10 or comparable module.
This makes the RX, TX, STATE, EN pin easy to connect to the bluetooth module.
This board only ensures that the voltage on the module is brought to 3.3V (from..
€1.50
Ex Tax:€1.24
Model: SEEED-110990444
These are the motor mounts for the standard 7mm coreless DC motors used for the Crazyflie 2.1 DIY drone. See the datasheet under the tab "Downloads" for more information.
Package contents:
4x Motor mount..
€6.50
Ex Tax:€5.37
Model: BOLTNUTSET-500PCS
A handy set with bolts and nuts of different sizes.
Specifications:
Form factor: ISO 7380
Thread: M3, M4 and M5
Material: Stainless steel
Package contents:
M3:
30x M3x8mm
30x M3x12mm
30x M3x16mm
30x M3x20mm
1..
€11.00
Ex Tax:€9.09
Model: BOLTNUTSET-1080PCS
A handy set with bolts, nuts, and washers of different sizes with corresponding Allen keys.
Specifications:
Form factor: DIN 912
Thread: M2, M3 and M4
Material: Stainless steel
Package contents:
1x Allen key for M2 bolt
1x A..
€15.00
Ex Tax:€12.40
Model: BOLTNUTWASHERSET-880PCS
A handy set with bolts, nuts, and washers of different sizes.
Specifications:
Form factor: ISO 7380
Thread: M2, M3, M4 and M5
Material: Stainless steel
Package contents:
M2:
30x M2x8mm
30x M2x12mm
30x M2x16mm
30..
€15.00
Ex Tax:€12.40
Model: STEPBRACK42
This bracket is suitable for stepper motors with 42 x 42mm dimensions. (eg NEMA17 motors)
The material is 3mm thick metal and is black in color. See the images for the dimensions of the bracket.
Note: No mounting tools are included with this br..
€2.50
Ex Tax:€2.07
Model: STEPBRACKNEMA17
This bracket is especially suitable for mounting a stepper motor.
Specifications:
Suitable stepper motors: NEMA17
Mounting orientation: Straight
Material: Metal
Color: Black
Thickness: ±3mm
Dimensions: See images
Package conte..
€3.00
Ex Tax:€2.48
Model: STEPBRACKNEMA17S
This bracket is especially suitable for mounting a stepper motor.
Specifications:
Suitable stepper motors: NEMA17
Mounting orientation: Straight
Material: Anodized aluminum
Color: Black
Thickness: ±2.5mm
Dimensions: See images
..
€3.00
Ex Tax:€2.48
Model: STEPBRACK57
This bracket is suitable for stepper motors with 57 x 57mm dimensions (e.g. NEMA23 motors).
The material is 3mm thick metal and is black in color. See the images for the dimensions of the bracket.
Note: No mounting tools are included with this ..
€3.00
Ex Tax:€2.48
Model: STEPBRACKNEMA23
This bracket is especially suitable for mounting a stepper motor.
Specifications:
Suitable stepper motors: NEMA23Mounting orientation: StraightMaterial: MetalColor: Black
Thickness: ±3mm
Dimensions: See images
Package contents:
1x Bra..
€3.50
Ex Tax:€2.89
Model: STEPBRACKNEMA11-17
This bracket is especially suitable for mounting a stepper motor. The slots instead of holes allow for multiple motor sizes.
Specifications:
Suitable stepper motors: NEMA11-NEMA17
Minimum distance between screw holes: 20mm
Maximum d..
€3.50
Ex Tax:€2.89
Model: BRASSBRUSH
This brass brush can, for example, be used to clean the hotend of your 3D printer (first warm up the hotend and make sure that no short circuit is made with the thermistor/heater cables).
Specifications:
Brush material: Brass with iron core&..
€1.00
Ex Tax:€0.83
Model: BB170PBLACK
A breadboard ideal for combining with an Arduino! (especially the Arduino Nano)
There are 85 holes on both sides.
At the bottom there is an adhesive layer for placement on a flat surface, system etc.
Dimensions: 47 x 35 x 9mm
Suitable for..
€1.50
Ex Tax:€1.24
Model: BB170PBLUE
Ideal for combining a breadboard with an Arduino! (especially the Arduino Nano)
There are 85 holes on both sides.
At the bottom is an adhesive layer for placement on a plate, system etc.
Dimensions: 47 x 35 x 9mm
Suitable for wires betwee..
€1.50
Ex Tax:€1.24
Model: BB170PGREEN
Ideal for combining a breadboard with an Arduino! (especially the Arduino Nano)
There are 85 holes on both sides.
At the bottom there is an adhesive layer for placement on a plate, system etc.
Dimensions: 47 x 35 x 9mm
Suitable for wires ..
€1.50
Ex Tax:€1.24
Model: BB170PRED
Ideal for combining a breadboard with an Arduino! (especially the Arduino Nano)
There are 85 holes on both sides.
At the bottom there is an adhesive layer for placement on a plate, system etc.
Dimensions: 47 x 35 x 9mm
Suitable for wires ..
€1.50
Ex Tax:€1.24
Model: BB170PTRANSP
Ideal for combining a breadboard with an Arduino! (especially the Arduino Nano)
There are 85 holes on both sides.
At the bottom there is an adhesive layer for placement on a plate, system etc.
Dimensions: 47 x 35 x 9mm
Suitable for wires ..
€1.50
Ex Tax:€1.24
Model: BB170PWHITE
A breadboard that can idealy be combined with an Arduino! (especially the Arduino Nano)
There are 85 holes available on each side.
There is adhesive layer on the bottom so you can stick it on a plate or system etc.
Dimensions: 47 x 35 x 9mm ..
€1.50
Ex Tax:€1.24
Model: BB170PYELLOW
Ideal for combining a breadboard with an Arduino! (especially the Arduino Nano)
There are 85 holes on both sides.
At the bottom there is an adhesive layer for placement on a plate, system etc.
Dimensions: 47 x 35 x 9mm
Suitable for wires ..
€1.50
Ex Tax:€1.24
Model: BB270P
A breadboard ideal to combine with an Arduino! (Especially an Arduino Nano)
Both sides contain 115 connection holes and a power supply rail with 20 holes.
Dimensions: 90 x 53 x 9mm
Suitable for wires between 20 and 29 AWG...
€2.50
Ex Tax:€2.07
Model: BB400P
A breadboard that is idealy combined with an Arduino!
For the power supply there are 100 points available, the mid section contains 300 points.
There is an adhesive layer on the bottem so you can stick it to a plate or system etc.
You can connect ..
€3.00
Ex Tax:€2.48
Model: BB400PTRANSP
A breadboard ideal for combining with an Arduino!
There are 100 points for the power supply, the centerpiece contains 300.
At the bottom there is an adhesive layer for placement on a flat surface, system etc.
Two (or more) of these breadboards can..
€3.00
Ex Tax:€2.48
Model: VM-SDAD102
A breadboard with 456 points, useful for prototyping.
Specifications:
Material:
Exterior plastic: ABS
Connections: Alloy of silver and nickel
Points: 456
Dimensions: 81 x 62 x 9 mm..
€7.50
Ex Tax:€6.20
Model: BB830P
A breadboard that is idealy combined with an Arduino!
For the power supply there are 200 points available, the mid section contains 630 points.
There is an adhesive layer on the bottem so you can stick it to a plate or system etc.
You can connect ..
€4.00
Ex Tax:€3.31
Model: BB830PTRANSP
A breadboard ideal for combining with an Arduino!
200 points are present for the power supply, the center piece contains 630.
At the bottom is an adhesive layer for placement on a flat surface, system etc.
Two (or more) of these breadboards can be..
€4.00
Ex Tax:€3.31
Model: BREAKOUT-ESP-01
This is a breakout board for an ESP-01(S) module with which it can easily be used on a breadboard, for example. The ESP-01 module must be mounted on the board in such a way that the 3.3V and RX pin are on the side of the capacitor...
€1.00
Ex Tax:€0.83
Model: ZD-10
With this budget soldering iron standard you can give your loose soldering iron a handy standard.
With this stand a sponge is supplied for cleaning the soldering tip.
Suitable for:
Budget Soldering Iron ZD-30C - 30W
Instructions for ..
€5.00
Ex Tax:€4.13
Model: ZD-30C
With this budget soldering iron you can solder well for a low price.
With this soldering iron a standard 1mm point is supplied with which you can do almost all the standard soldering work.
Specifications:
Voltage: 230VAC
Power sol..
€8.00
Ex Tax:€6.61
Model: ZD-99KIT
This kit with a budget soldering station and lots of accessories is a good base to start soldering.
Specifications ZD-99 soldering iron:
Input voltage: 230VAC
Soldering iron power: 48W
Temperature adjustable with a range of 150-480°C (on..
€25.00
Ex Tax:€20.66
Model: VTSS5
With this budget soldering station you can easily solder for a low price.
A standard 1mm tip is supplied with this soldering station with which you can perform both large and small soldering work.
Specifications:
Voltage: 230VAC
S..
€22.00
Ex Tax:€18.18
Model: ZD-99
With this budget soldering station you can solder perfectly for a low price.
At this soldering station a standard 1mm point is supplied with which you can do almost all the standard soldering work.
Specifications:
Voltage: 230VAC
..
€17.50
Ex Tax:€14.46
Model: CABLEGLANDM12
An M12 cable gland to make a waterproof cable entry.
Specifications:
Color: Gray
Material: Polyamide
Cable thickness: 3.0 - 6.5mm
Dimensions: See the datasheet under the tab "Downloads".
IP67 rating (if cable gland and cabl..
€0.60
Ex Tax:€0.50
Model: CABLEGLANDM16
An M16 cable gland to make a waterproof cable entry.
Specifications:
Color: Gray
Material: Polyamide
Cable thickness: 6.5 - 8.0mm
Dimensions: See the datasheet under the tab "Downloads".
IP67 rating (if cable gland and cabl..
€0.70
Ex Tax:€0.58
Model: CABLEGLANDM20
An M20 cable gland to make a waterproof cable entry.
Specifications:
Color: Gray
Material: Polyamide
Cable thickness: 8.0 - 12.0mm
Dimensions: See the datasheet under the tab "Downloads".
IP67 rating (if cable gland and cab..
€0.85
Ex Tax:€0.70
Model: CABLEGLANDM25
An M25 cable gland to make a waterproof cable entry.
Specifications:
Color: Gray
Material: Polyamide
Cable thickness: 12.0 - 18.0mm
Dimensions: See the datasheet under the tab "Downloads".
IP67 rating (if cable gland and cable are co..
€1.50
Ex Tax:€1.24
Model: CASETPA3116-2X50-1x100
A kit to build a transparent case for a TPA3116 amplifier.
Specifications:
Suitable for:
TPA3116 2x50W and 1x100W Audio Amplifier - Bass-Treble Control
TPA3116 2x50W and 1x100W Audio Amplifier - Bluetooth 4.2 - Bass-Treble Control
..
€9.00
Ex Tax:€7.44
Model: CASETPA3116-2X50
A kit to build a transparent case for a TPA3116 amplifier.
Specifications:
Suitable for:
TPA3116 2x50W Audio Amplifier
Dimensions: 104 x 74 x 51mm
Package contents:
Enclosure:
6x Acrylic panel
4x M3 bolt 20m..
€11.00
Ex Tax:€9.09
Model: CASETPA3116-2X50BMT
A kit to build a transparent case for a TPA3116 amplifier.
Specifications:
Suitable for:
TPA3116 2x50W Audio Amplifier - Bass-Mid-Treble Control
TPA3116 2x50W Audio Amplifier - Bluetooth 4.2 - Bass-Mid-Treble Control
Dimensi..
€12.50
Ex Tax:€10.33
Model: VM-WSSA100B
This kit contains everything you need to builld your own christmas tree with lights. An extended manual is included in this kit.
Note: 9V Battery is not included...
€8.50
Ex Tax:€7.02
Model: DUPONTCLIPBLACK
This is widely used when you want to measure on the pins of a component.
You can connect this clip to a female dupont plug.
Almost indispensable in combination with the Logic Analyzer - 8 channel - USB...
€0.80
Ex Tax:€0.66
Model: DUPONTCLIPBLUE
This is widely used when you want to measure on the legs of a component.
You can connect this clip to a female dupont plug.
Almost essential in combination with the Logic Analyzer - 8 channel - USB...
€0.80
Ex Tax:€0.66