Model: 5MMLEDHOLD100X
A set of LED holders for 5mm LEDs...
€3.00
Ex Tax:€2.48
Model: 74HC00N
The 74HC00N is a quad 2-input NAND gate integrated circuit that outputs a low signal only when both inputs are high, widely used in digital logic circuits...
€0.60
Ex Tax:€0.50
Model: 74HC02N
The 74HC02N is a quad 2-input NOR gate integrated circuit that outputs a high signal only when both inputs are low, making it essential for various digital logic applications...
€0.60
Ex Tax:€0.50
Model: 74HC08N
The 74HC08 is a quad 2-input AND gate integrated circuit used for performing logical AND operations in digital circuits...
€0.60
Ex Tax:€0.50
Model: 74HC14
With this chip you can invert a signal with a Schmitt trigger. A Schmitt trigger is a switch that has two voltage thresholds. When the input voltage exceeds the upper level the signal becomes low and when the input voltage falls below the lower level..
€0.50
Ex Tax:€0.41
Model: 74HC595
The ideal way to create more output. You can easily control 8 LEDs with this chip and control it via an SPI...
€0.50
Ex Tax:€0.41
Model: 78L05
Standard positive 5V voltage regulator in TO-92 package. Is widely used to make a neat 5V line.
This controller can deliver up to 100mA and has an input voltage of 7-20V.
For more information see the datasheet under the tab "Downloads".
This pro..
€0.35
Ex Tax:€0.29
Model: 8PSOCKET
Easy to use as a spacer. E.g. if you want to put a chip on a printed circuit board and prevent the chip from overheating during soldering.
It is also useful if you know in advance that it is possible that your chip can go wrong. With an IC foot you ..
€0.30
Ex Tax:€0.25
Model: 8PSOCKETDBL
This IC foot is suitable for soldering on both sides (from top and bottom)..
€0.60
Ex Tax:€0.50
Model: ESP8266-07S-4M
This ESP-07S is a version of the ESP8266 module series with 4MB memory and has an uFL connector on board for an external Wi-Fi antenna. (this has to be purchased separately!)
This module offers you the possibility to connect your Arduino to Wi-Fi ..
€5.00
Ex Tax:€4.13
Model: ESP8266-12F-4M
This module offers you the possibility to connect your Arduino to Wi-Fi for a very low price.
The ESP8266 module works with the normal UART port on your Arduino and can connect to networks, form your own network (hot spot) or both. The possibiliti..
€5.00
Ex Tax:€4.13
Model: ESP8266-12S-4M
This ESP-12S is an improved model with respect to the ESP-12F module, but is not a direct replacement in connection with the missing pins at the bottom of the module. Since these pins are not used in most cases, it is in most cases a replacement for ..
€4.50
Ex Tax:€3.72
Model: RK09K1130C17
A logarithmic potentiometers of 10KΩ with one turn and handy knob.
The footprint is compatible with RV09 potentiometers from Taiwan Alpha and RK09K potentiometers from Alps.
See the images for the dimensions of this potentiometer.
If..
€2.75
Ex Tax:€2.27
Model: AMS1117-3.3
Standard positive 3.3V voltage regulator in SOT-223 package. Is widely used to make a neat 3.3V line...
€0.50
Ex Tax:€0.41
Model: AMS1117-5.0
Standard positive 5V voltage regulator in SOT-223 package. Is widely used to make a neat 5V line.
For more information: Datasheet...
€0.50
Ex Tax:€0.41
Model: AMS1117-5.0S-5V
Standard positive 5V voltage regulator in SOT-89 package. Is widely used to make a neat 5V line...
€0.50
Ex Tax:€0.41
Model: APS6404L-3SQR-SN
This PSRAM chip can be used on e.g. a Teensy 4.1.
See the following page for more information: Teensy psram..
€3.00
Ex Tax:€2.48
Model: AT328KIT
With this ATmega328P (Programmed with UNO bootloader) you can (for example) build your Arduino on a breadboard.
Package contents:
1x ATmega328P DIP package 28-pins
1x 16MHz crystal
2x 20pF or 22pF capacitor (needed for the crystal)
..
€6.00
Ex Tax:€4.96
Model: ATTINY85-20PU
The ATtiny85 can be used to create small and compact circuits. The ATtiny85 can be programmed by a microcontroller, for example an Arduino Uno as ISP or with an USBasp AVR Programmer.
While the ATtiny85 has only 6 functional pins, it is still quit..
€3.00
Ex Tax:€2.48
Model: EI14-600:600
A simple audio transformer that, for example, allows you to remove noise caused by a ground loop.
Specifications:
Frequency range: 20-20000Hz
DC Resistance coil 1: 140Ω±20%
DC Resistance coil 2: 140Ω±20%
Rated AC resistance coil 1: 600..
€1.00
Ex Tax:€0.83
Model: BTLED3MM
Diameter (mm): 3mm
Color: Blue
Lens type: Clear
Reverse Current (uA): <= 3
Lifetime: 100,000 hours
Viewing angle : 20 ~ 25 Degrees
Absolute Maximum Ratings (Ta = 25°C)
Max Power Dissipation: 80mw
Max Continuous Forward Current: 24mA
Max P..
€0.10
Ex Tax:€0.08
Model: BLED3MM
A simple blue 3mm LED.
Do not forget the LED series resistor! (this can be found at the resistors)
At 5V: 330Ω Resistor
At 3.3V: 150Ω Resistor..
€0.10
Ex Tax:€0.08
Model: BLED5MM
Diameter (mm): 5mm
Color: Blue
Lens type: Diffused
Nominal Voltage: 3.0-3.2V
Nominal Current: 20mA
Do not forget the LED series resistor! (this can be found at the resistors)
At 5V: 82 Ω (click here)
At 3.3V: no resistance ..
€0.10
Ex Tax:€0.08
Model: MOV-10D561K
A standard metal oxide varistor. This varistor can be used as a safety component for our Hi-Link PCB power supplies, for example...
€0.75
Ex Tax:€0.62
Model: BCAP-12X12X7.3MM-BLACK
This button cap fits our Tactile Pushbutton Switch Momentary 4pin 12x12x7.3mm. So you can use it to make your button prettier and easier to use.
Specifications:
Color: Black
Dimensions: See image..
€0.15
Ex Tax:€0.12
Model: BCAP-12X12X7.3MM-BLUE
This button cap fits our Tactile Pushbutton Switch Momentary 4pin 12x12x7.3mm. So you can use it to make your button prettier and easier to use.
Specifications:
Color: Blue
Dimensions: See image..
€0.15
Ex Tax:€0.12
Model: BCAP-12X12X7.3MM-GREEN
This button cap fits our Tactile Pushbutton Switch Momentary 4pin 12x12x7.3mm . So you can use them to make your button prettier and easier to use.
Specifications:
Color: Green
Dimensions: See image..
€0.15
Ex Tax:€0.12
Model: BCAP-12X12X7.3MM-RED
This button cap fits our Tactile Pushbutton Switch Momentary 4pin 12x12x7.3mm. So you can use it to make your button prettier and easier to use.
Specifications:
Color: Red
Dimensions: See image..
€0.15
Ex Tax:€0.12
Model: BCAP-12X12X7.3MM-WHITE
This button cap fits our Tactile Pushbutton Switch Momentary 4pin 12x12x7.3mm. So you can use it to make your button prettier and easier to use.
Specifications:
Color: White
Dimensions: See images..
€0.15
Ex Tax:€0.12
Model: BCAP-12X12X7.3MM-YELLOW
This button cap fits our Tactile Pushbutton Switch Momentary 4pin 12x12x7.3mm. So you can use it to make your button prettier and easier to use.
Specifications:
Color: Yellow
Dimensions: See images..
€0.15
Ex Tax:€0.12