LilyGO T5-4.7 inch S3 E-paper E-ink ESP32-S3 - with JST-PH Li-Po Connector - Soldered Headers
- Availability: Directly available from warehouse in Eindhoven
- SKU: 004992
€44.50
Ex Tax: €36.78
This TTGO T5 from LilyGO is a microcontroller based on an ESP32-S3 with a built-in 4.7 inch E-paper E-ink display. The board has a USB-C connection with which the module can be powered and programmed. There is also a connection with which the board can be powered by a Li-Po/Li-ion.
Note: The display may not yet be properly sticked to the circuit board, so be careful when removing it from the packaging.
Note: The polarity of the battery cable may not be correct, check the plus and minus carefully with the indication on the PCB (the polarity on the PCB is correct)!
See the following page for more information: GitHub
Reviews Over LilyGO T5-4.7 inch S3 E-paper E-ink ESP32-S3 - with JST-PH Li-Po Connector - Soldered Headers
This product has 0 review(s) in total.
Report this review.
Tags:
Microcontroller Boards
, With Bluetooth
, LilyGO T5-4.7 inch S3 E-paper E-ink ESP32-S3 - with JST-PH Li-Po Connector - Soldered Headers
, 004992
, LilyGO TTGO
, H580
, Programmable button(s)
, Microcontroller (MCU)
, SD-card adapter
, Battery charger
, Display
, RTC
, Native USB
, USB CDC
, UART
, GPIO
, SPI
, PWM
, I2S
, I2C
, ADC
, Bluetooth
, Wi-Fi
Specifications
| General | |
| Brand | LilyGO TTGO |
| Manufacturer model/SKU | H580 |
| Model revision | V2.4 |
| Features | RTC Display Battery charger SD-card adapter Microcontroller (MCU) Programmable button(s) |
| General physical appearance | |
| Main color | Black |
| Weight [g] | 38 |
| Dimension X [mm] | 118 |
| Dimension Y [mm] | 63 |
| Form factor | Module (general) |
| General electrical properties | |
| Minimum supply voltage [V DC] | 5 (lower possible via Li-ion/Li-Po battery) |
| Maximum supply voltage [V DC] | 5 |
| Minimum IO-pin input voltage [V] | 3.3 |
| Maximum IO-pin input voltage [V] | 3.3 |
| IO-pin output voltage [V] | 3.3 |
| Maximum IO-pin source current [mA] | 40 |
| Maximum IO-pin sink current [mA] | 28 |
| MCU | |
| Manufacturer | Espressif |
| Chip series | ESP32-S3 |
| Maximum clock frequency [MHz] | 240 |
| Number of cores | 2 |
| Internal memory | |
| SRAM [KB] | 512 |
| PSRAM [MB] | 8 |
| Flash memory [MB] | 16 |
| EEPROM type | Emulated |
| Communication | |
| Hardware interface(s) | ADC I2C I2S PWM SPI GPIO UART USB CDC Native USB |
| Number of IO-pins | 11 |
| Maximum available hardware PWM channels | 8 |
| Maximum available analog input pins (ADC) | 5 |
| Maximum available analog output pins (DAC) | 0 |
| Maximum available hardware UART interfaces | 3 |
| Maximum available hardware I2C interfaces | 2 |
| Maximum available hardware SPI interfaces | 2 |
| USB to serial converter | Integrated into microcontroller |
| Supported SD card size | Micro SD |
| Wireless communication | |
| Interface(s) | Wi-Fi Bluetooth |
| Wi-Fi chip/SoC | ESP32-S3 |
| Wi-Fi frequency [GHz] | 2.4 |
| Bluetooth chip/SoC | ESP32-S3 |
| Bluetooth version | 5.0 |
| Supported Bluetooth standard(s) | LE |
| Display | |
| Type | E-paper |
| Driver | ED047TC1 |
| Screen diagonal [inch] | 4.7 |
| Number of pixels long side | 960 |
| Number of pixels short side | 540 |
| Pixel colors | Gray Black White |
| Maximum refresh rate [Hz] | 1.59 |
| Partial display refresh | Yes |
| RTC | |
| RTC chip | PCF8563 |
| Back-up battery/capacitor | Yes |
| Battery circuit | |
| Battery charger chip/SoC | HX6610 |
| Supported battery chemistry | Li-Po Li-ion |
| Maximum charging voltage [V] | 4.2 |
| Maximum charging current [mA] | 500 |
| Adjustable charging current | No |
| Protection circuit | No |
| Connectors | |
| Power supply connector(s) | USB-C female Pin header female (2.54mm) |
| IO-connector(s) | USB-C female CJT A2004 male Pin header female (2.54mm) |
| Battery connector(s) | JST-PH (compatible) male |
| Wi-Fi/Bluetooth antenna connector | Built-in antenna |
| Package contents | |
| Package contents | 1x TTGO T5 4.7 inch S3 1x Battery cable |