Waveshare RP2350-Touch-LCD-1.28 Board with 1.28 Inch Round Display with Touchscreen and IMU
- Availability: Directly available from warehouse in Eindhoven
- SKU: 006913
€20.50
Ex Tax: €16.94
A development board from Waveshare based on a RP2350 microcontroller by Raspberry Pi with multiple sensors. Thanks to the built-in USB connector, it is easy to program. Things can be shown on the built-in IPS display and with the touchscreen, an extensive user interface can be created. Finally, the board has a battery connector where a Li-Po/Li-ion battery (not included) can be connected, which can also be charged via the board.
See the following page for more information: Wiki
Reviews Over Waveshare RP2350-Touch-LCD-1.28 Board with 1.28 Inch Round Display with Touchscreen and IMU
This product has 0 review(s) in total.
Report this review.
Tags:
Microcontroller Boards
, Others
, Waveshare RP2350-Touch-LCD-1.28 Board with 1.28 Inch Round Display with Touchscreen and IMU
, 006913
, Waveshare
, 29025
, Battery charger
, Display
, Microcontroller (MCU)
, Touchscreen
, Battery protection circuit
, Acceleration sensor
, Gyroscope
, I2C
, SPI
, Native USB
, UART
, PWM
, ADC
, GPIO
, PIO
, USB CDC
Specifications
| General | |
| Brand | Waveshare |
| Manufacturer model/SKU | 29025 |
| Features | Display Gyroscope Touchscreen Battery charger Acceleration sensor Microcontroller (MCU) Battery protection circuit |
| General physical appearance | |
| Main color | Black |
| Weight [g] | 12 |
| Dimension X [mm] | 41 |
| Dimension Y [mm] | 39 |
| Dimension Z [mm] | 8 |
| Form factor | Module (general) |
| General electrical properties | |
| Minimum supply voltage [V DC] | 3.3 |
| Maximum supply voltage [V DC] | 5 |
| Minimum IO-pin input voltage [V] | 3.3 |
| Maximum IO-pin input voltage [V] | 3.3 |
| IO-pin output voltage [V] | 3.3 |
| Maximum IO-pin source current [mA] | 12 |
| Maximum IO-pin sink current [mA] | 12 |
| MCU | |
| Manufacturer | Raspberry Pi |
| Chip series | RP2350 |
| Maximum clock frequency [MHz] | 150 |
| Number of cores | 2 |
| Internal memory | |
| SRAM [KB] | 520 |
| PSRAM [MB] | 0 |
| Flash memory [MB] | 16 |
| EEPROM type | Emulated |
| Communication | |
| Hardware interface(s) | ADC I2C PIO PWM SPI GPIO UART USB CDC Native USB |
| Number of IO-pins | 6 |
| Maximum available hardware PWM channels | 6 |
| Maximum available analog input pins (ADC) | 3 |
| Maximum available analog output pins (DAC) | 0 |
| Maximum available hardware UART interfaces | 2 |
| Maximum available hardware I2C interfaces | 2 |
| Maximum available hardware SPI interfaces | 1 |
| USB to serial converter | Integrated into microcontroller |
| Display | |
| Type | IPS |
| Driver | GC9A01 |
| Screen diagonal [inch] | 1.28 |
| Number of pixels long side | 240 |
| Number of pixels short side | 240 |
| Display shape | Round |
| Pixel colors | RGB |
| Touchscreen | |
| Touchscreen controller | CST816 |
| Touch type | Capacitive |
| Acceleration sensor | |
| Sensor chip/SoC | QMI8658A |
| Degrees of freedom (DOF) | 3 |
| Maximum measuring range [±g] | 16 |
| Maximum resolution [bit] | 16 |
| Gyroscope | |
| Sensor chip/SoC | QMI8658A |
| Degrees of freedom (DOF) | 3 |
| Maximum measuring range [±°/s] | 2048 |
| Maximum resolution [bit] | 16 |
| Battery circuit | |
| Battery charger chip/SoC | ETA6098 |
| Supported battery chemistry | Li-Po Li-ion |
| Maximum charging voltage [V] | 4.2 |
| Maximum charging current [mA] | 1000 |
| Adjustable charging current | No |
| Protection circuit | No |
| Connectors | |
| Power supply connector(s) | USB-C female JST-SH (compatible) male |
| IO-connector(s) | USB-C female JST-SH (compatible) male |
| Battery connector(s) | Molex Picoblade (compatible) male |
| Package contents | |
| Package contents | 1x RP2350-LCD-1.28 board 1x JST-SH to DuPont female cable |