Menu
Your Cart

Touch

Model: DFROBOT-SEN0285
..
€15.50
Ex Tax:€12.81
Model: LILYGO-H479
This 4.7 inch capacitive touchscreen from LilyGO is specially made for the TTGO T5 V3 with 4.7 inch E-ink/E-paper display. Currently there are two types of TTGO T5 V3 modules available for which this touchscreen is suitable: LilyGO TTGO T5 4..
€14.00
Ex Tax:€11.57
Model: M5STACK-A066
This is an M5Stack FACES fingerprint module. Specifications: Interface Serial UART2 (16/17) FPC1020A algorithm chip Sensor surface area: 192*192 Pixels Pixel resolution: 256 grayscale levels (8 Bit) Operating temperature: - 40 to + 8..
€18.00
Ex Tax:€14.88
Model: M5STACK-U074
The M5Stack Finger Print Hat is an add-on for the M5StickC* with a built-in FPC1020SC fingerprint sensor.  Specifications: Built-in FPC1020SC sensor Designed for use with M5StickC* UART communication UART settings: Baudrate:..
€24.00
Ex Tax:€19.83
Model: M5STACK-U008
The M5Stack Finger Print Unit is a fingerprint sensor module with built-in FPC1020A.  Specifications: Built-in FPC1020A sensor 2x LEGO® holes for mounting Grove interface UART communication UART settings: Baudrate: 19200bp..
€22.00
Ex Tax:€18.18
Model: MPR121
The MPR121 touch module can read up to 12 channels of touch. 8 channels can also be used to control LEDs. The module works via I2C and operates at a voltage between 2.5 and 3.6VDC. Do you want to get started with this module? Look here: Sensing ..
€4.00
Ex Tax:€3.31
Model: RD4x4TTP229
A 4x4 touch module suitable for the RobotDyn Touch Module TTP229- LSF 16-channel. 15cm cables are supplied for connecting to the  RobotDyn Touch Module TTP229-LSF 16-channel...
€4.00
Ex Tax:€3.31
Model: RDDISKPADTTP229
A Disk Pad touch module suitable for the RobotDyn Touch Module TTP229 -LSF 16-channel. 15cm cables are supplied for connecting to the  RobotDyn Touch Module TTP229-LSF 16-channel...
€4.00
Ex Tax:€3.31
Model: TOUCH1CHBLUE
A small touch square that glows blue when you press it with your finger and can transmit a signal (touch works capacitively). This module remains on after contact and only turns off when it is touched (can therefore be used as on/off switch). The m..
€3.00
Ex Tax:€2.48
Model: TOUCH1CHGREEN
A small touch surface that glows green when you press it and can transmit a signal (touch works capacitively). This module stays on after contact and only goes out when it is touched (can therefore be used as on/off switch). The module operates at ..
€3.00
Ex Tax:€2.48
Model: TOUCH1CHRED
A small touch area that glows red when you press it with your finger and can pass a signal (touch works capacitively). This module remains on after contact and only goes out when it is touched (can therefore be used as on/off switch). The module op..
€3.00
Ex Tax:€2.48
Model: TOUCH1CHYELLOW
A small touch square that glows yellow when you press it with your finger and can pass a signal (touch works capacitively). This module remains on after contact and only goes out when it is touched (can therefore be used as on/off switch). The modu..
€3.00
Ex Tax:€2.48
Model: TTP223B
A 1 channel touch module. Specifications: Voltage: 2.0 - 5.5VDC (on the Vcc and GND) 1 LED to show the status of the touch. 1 put pin for the touch status (SIG pin) Dimensions:  24 x 24mm..
€2.50
Ex Tax:€2.07
Model: TTP223BRED
A 1 channel touch module. Specifications: Voltage: 2.0 - 5.5VDC (on the Vcc and GND) 1 LED to show the status of the touch. 1  output pin for the touch status (I/O pin) Option for high/low output and function as Reset butto..
€1.00
Ex Tax:€0.83
Model: TTP224
A 4 channel touch module. Specifications: Voltage: 2.4 - 5.5VDC (on the Vcc and GND) 4 LEDs to show the status of the touch. 4 output pins for the touch status Dimensions: 35 x 29 mm Note: The module may be delivered with separate..
€3.00
Ex Tax:€2.48
Model: TTP229
A 16 channel touch module. Specifications: Voltage: 2.4 - 5.5VDC (on the Vcc and GND) 16 output pins for touch status Possible to read the pins serially (SCL and SDO) Note: This is not I2C! Dimensions:  49 x 65mm For more informat..
€4.00
Ex Tax:€3.31
Waveshare Capacitive Fingerprint Reader
2-4 Weeks
Model: WS-13694
With this module a fingerprint can be read with a PC, Raspberry Pi, Arduino or other microcontroller. The fingerprint reader is connected via UART or USB. Specifications: Supply voltage: 3.3-5V DC Signal voltage: 3.3-5V Communication: ..
€47.00
Ex Tax:€38.84
Showing 1 to 17 of 17 (1 Pages)
1
false
true
true
Remove
Change
tr