Model: TD-8130MG-CONT
A very powerful servo that is easy to control. It comes with a few pieces of plastic that you can mount on it, to which you can then mount other things. This servo is splashproof.
Note: This servo can draw relatively high currents, especially with..
€14.50
Ex Tax:€11.98
Model: T050000
The TinkerKit Braccio is a fully operational robotic arm, controlled via Arduino. It can be assembled in a variety of ways for multiple tasks such as picking up objects. It is also possible to attach a camera or solar panel to the arm. The Braccio ro..
€220.00
Ex Tax:€181.82
On request
Model: TMC2130DRIVERMODV1.1
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer.
This V1.1 has the SPI pins soldered upwards so that they are accessible from above.
Specifications:
Voltage range(VM): 5.5-45V
Volt..
€10.50
Ex Tax:€8.68
Model: TMC2208DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer.
Specifications:
Voltage range(VM): 5.5-36V
Voltage range(VIO): 3.3-5V
Maximum current: 1.2A per phase (continuous, with cooling), ..
€8.00
Ex Tax:€6.61
Model: TMC2209DRIVERMODV3.1
This driver module is almost identical to the TMC2209 Motor Driver Module, this module does not have the UART pins on the top, but on the bottom.
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D pri..
€8.50
Ex Tax:€7.02
Model: TMC2225DRIVERMODV1.1
This TMC2225 is similar to the TMC2208 Motor Driver. This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer.
Specifications:
Motor voltage range (VM): 4.75-36V
Logic voltage range (VIO): 3..
€8.50
Ex Tax:€7.02
New
Model: TMC2226DRIVERMODV1.1
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer. Compared to many other stepper motor drivers, this one has a number of special features, including:
StealthChop2™ technology for qui..
€8.75
Ex Tax:€7.23
On request
Model: TMC5160DRIVERMOD
This stepper motor driver module can be used separately or in combination with a CNC shield or 3D printer.
This stepper motor driver is intended for motors with a higher power and amperage, suitable for, among other things, NEMA17 and NEMA23.
Spe..
€24.00
Ex Tax:€19.83
Model: TO220HEATSINK
A heatsink kit for components based on the TO-220 package. The heatsink comes with mounting material.
Specifications:
Dimensions cooling block: 20 x 14.5 x 9.5 mm
Package Contents:
1x Aluminum heat sink for TO-220
1x M3 5m..
€0.80
Ex Tax:€0.66
Model: TS90D-CONT
A small continuous rotation servo that is easy to control. It comes with a few pieces of plastic* that you can mount on it, to which you can then mount other things.
*Note: The supplied plastic attachments may differ from the plastic pieces shown ..
€4.50
Ex Tax:€3.72
Model: TS90M
A small servo that is easy to control. It comes with a few pieces of plastic that you can mount on it, to which you can then mount other things.
Note: If the servo has less than 180 degrees range, the minimum (500us) and maximum pulse width (2500u..
€5.00
Ex Tax:€4.13
Model: TS90M-CONT
A small continuous rotation servo that is easy to control. It comes with a few pieces of plastic that you can mount on it, to which you can then mount other things...
€5.00
Ex Tax:€4.13
Model: ULN2003
The ULN2003 is an array of seven Darlington transistor pairs. With this, a signal can be amplified to 50V and 500mA per channel. The signal pins work with both 3.3V and 5V logic. The built-in flyback diodes protect the chip against inductive loads, s..
€0.50
Ex Tax:€0.41
Model: MISTMODULE
This ultrasonic fog module can be easily used to create fog. To make the fog, the stick must be placed in water with one side and the piezo disc must be held on the other end.
Specifications:
Supply voltage: 5V DC
Current draw: ~300mA..
€4.00
Ex Tax:€3.31
Model: JT-DC3W-HORI
An underwater pump (horizontal version) suitable for a 6mm hose.
Specifications:
Voltage range: 3-6V DC
Current: ~ 150-200 mA (depending on voltage and pressure)
Pump speed: approx. 80 L/hour
Diameter output: 6mm inside size (hose must..
€4.00
Ex Tax:€3.31
Model: JT-DC3W-VERT
An underwater pump (vertical version) suitable for a 6mm hose.
Specifications:
Voltage range: 3-6V DC
Current: ~ 150-200 mA (depending on voltage and pressure)
Pump speed: approx. 80 L/hour
Diameter output: 6mm inside size (hose must h..
€4.00
Ex Tax:€3.31
New
Model: VIBDCMOTOR
A small vibration (DC) motor.
Note: The thin wires can vibrate loose if the motor and cabling are not properly secured in your setup. Use hot glue or other glue to protect these thin wires from loosening by vibration...
€1.75
Ex Tax:€1.45
Model: VIBRATEMODULE
A small flat vibration (DC) motor module with 3 pin headers for easy connection and 2 mounting holes for easy mounting.
Note: The motor is only secured with an adhesive layer. In situations where the motor is on for a long time, when it can get wa..
€2.50
Ex Tax:€2.07
Model: VIBRATEMODULE-SMALL
A small flat vibration (DC) motor module with a mounting hole for easy mounting.
Note: The motor is only secured with an adhesive layer. In situations where the motor is on for a long time, when it can get warm and/or when external force can be ap..
€2.50
Ex Tax:€2.07
2-4 Weeks
Model: 385PUMP12V
A water pump suitable for a 6mm hose.
Specifications:
Maximum voltage: 12V DC
Maximum current: ~400 mA (depending on voltage and pressure)
Maximum pump speed: ~108 L/hr
Hose coupling diameter: 7~8.5mm (suitable for hoses with ~6mm inne..
€6.00
Ex Tax:€4.96
Model: JT-DC3W-TUBE
Transparent hose suitable for submersible pumps with a connection of approx. 6mm.
Specifications:
Inside diameter: 6mm
Outside diameter 8mm
Only suitable for our submersible pumps with a relatively low pressure
Only suitable for clean,..
€1.50
Ex Tax:€1.24
On request
Model: JT-DC3W-TUBE-20CM
Transparent hose suitable for submersible pumps with a connection of approx. 6mm. This can also be used with the SDS011 dust sensor.
Specifications:
Inside diameter: 6mm
Outside diameter 8mm
Only suitable for our submersible pumps with a..
€0.50
Ex Tax:€0.41
New
Model: WS-19764
Brand: Waveshare
A DC motor driver module with 4 channels specially made for the Raspberry Pi Pico. The module has a built-in voltage converter that can power the Raspberry Pi Pico, so there is no need for a separate power supply for the Pico and the motors. Due to t..
€19.50
Ex Tax:€16.12
Model: WS-9724
Brand: Waveshare
With this Motor Control Shield you can control up to four DC motors or two stepper motors at the same time. With a jumper, the power supply circuit for the motors can be adjusted so that it receives a variable output voltage. Doing so allows motors w..
€9.00
Ex Tax:€7.44
-for-raspberry-pi-default-200x200.jpg "Waveshare Servo Driver HAT (B) for Raspberry Pi")
Model: WS-17035
Brand: Waveshare
With this HAT you provide a Raspberry Pi with a 16-channel PWM/servo control via I2C. The HAT is designed for the Raspberry Pi Zero, but also works with other models. In addition, the module can also be used with other microcontrollers such as an Ard..
€15.00
Ex Tax:€12.40
Model: WS-15275
Brand: Waveshare
With this HAT you provide a Raspberry Pi with a 16-channel PWM/servo control via I2C. The HAT is designed for the Raspberry Pi Zero, but also works with other models. In addition, the module can also be used with other microcontrollers such as an Ard..
€11.00
Ex Tax:€9.09
Model: WS-15669
Brand: Waveshare
With this HAT for Raspberry two stepper motors can be controlled. The module also has a built-in voltage converter that can be used to power the Raspberry Pi.
Specifications:
Supply voltage: 8.2-28V DC (via 5.5mm DC jack)
Signal voltage: 3..
€24.00
Ex Tax:€19.83
2-4 Weeks
Model: ZK-PP2K
A handy PWM controller for driving and testing DC motors. This controller has 2 different operation modes with which the behavior of the DC motor can be set. In addition to the buttons on the front of the screen of this controller, there is another c..
€9.00
Ex Tax:€7.44